3M™ Dyneon™ Fluoroplastic ET 6210AZ

About
3M™ Dyneon™ Fluoroplastic Agglomerate ET 6210AZ is a melt processable fluoroplastic consisting mainly of alternating tetrafluoroethylene and ethylene monomer units (ETFE). This partially crystalline fluorothermoplastic offers a valuable combination of properties. This agglomerate form can also be used for compounding. Features and Benefits Wide service temperature range -200° to +150°C Low flammability Excellent electrical and mechanical properties Very good resistance to solvents and chemicals High resistance to outdoor weathering High light transmission in the visible and UV ranges Non-stick characteristics Excellent tear resistance Low permeability Good resistance to radiation&&

About

3M™ Dyneon™ Fluoroplastic Agglomerate ET 6210AZ is a melt processable fluoroplastic consisting mainly of alternating tetrafluoroethylene and ethylene monomer units (ETFE). This partially crystalline fluorothermoplastic offers a valuable combination of properties. This agglomerate form can also be used for compounding. Features and Benefits Wide service temperature range -200° to +150°C Low flammability Excellent electrical and mechanical properties Very good resistance to solvents and chemicals High resistance to outdoor weathering High light transmission in the visible and UV ranges Non-stick characteristics Excellent tear resistance Low permeability Good resistance to radiation&&

Product Description
Generic	ETFE
Material Status	Commercial: Active
Features	Weather resistance is good,No viscosity,Gamma radiation,Good tear strength,Copolymer,Solvent resistance
Availabilitys	North America,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.72	g/cm³	ISO 12086
Melt Flow Rate
297℃，5.0kg	9.0	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	1200	MPa	ISO 527-2
tensile strength
Fracture, 23 ℃	50.0	MPa	ISO 527-2
Tensile strain
Fracture, 23 ℃	450	%	ISO 527-2

THERMAL	Nominal value	Unit	Test method
Melting temperature	266	℃	ISO 12086

Electrical performance	Nominal value	Unit	Test method
Dielectric strength
0.25 mm	59	kV/mm	ASTM D149
Dielectric constant
23 ℃，1 MHz	2.58		ASTM D150

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Extreme oxygen index	35	%	ASTM D2863

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel temperature	40	°C
Barrel 1 zone temperature	250	°C
Barrel 2 zone temperature	290	°C
Barrel 3 zone temperature	305	°C
Barrel 4 zone temperature	305	°C
Barrel 5 zone temperature	305	°C
Nozzle temperature	310	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.