3M™ Dyneon™ Fluoroplastic ET 6235Z

About
3M™ Dyneon™ Fluoroplastic ET 6235Z is a partially fluorinated copolymer comprising tetrafluoroethylene and ethylene and is belonging to the product class ETFE. It was designed primarily for film extrusion. Special Features Extremely high weathering and UV stability Wide service temperature range (-200 to +150°C) Excellent tear and tear propagation resistance Very good non-stick characteristics Good resistance to high energy radiation High light transmission in the visible and UV-A range Low flammability Excellent mechanical properties Very good resistance to solvents and chemicals Low permeability&&

About

3M™ Dyneon™ Fluoroplastic ET 6235Z is a partially fluorinated copolymer comprising tetrafluoroethylene and ethylene and is belonging to the product class ETFE. It was designed primarily for film extrusion. Special Features Extremely high weathering and UV stability Wide service temperature range (-200 to +150°C) Excellent tear and tear propagation resistance Very good non-stick characteristics Good resistance to high energy radiation High light transmission in the visible and UV-A range Low flammability Excellent mechanical properties Very good resistance to solvents and chemicals Low permeability&&

Product Description
Generic	ETFE
Material Status	Commercial: Active
Features	Weather resistance is good,No viscosity,Good Clarity,Gamma radiation,Good tear strength,Copolymer,Solvent resistance,V-0
Availabilitys	North America,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.72	g/cm³	ISO 12086
Melt Flow Rate
297℃，5.0kg	10	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	1200	MPa	ISO 527-2
tensile strength
Fracture, 23 ℃	50.0	MPa	ISO 527-2
Tensile strain
Fracture, 23 ℃	450	%	ISO 527-2

elastic body	Nominal value	Unit	Test method
tear strength	500	kN/m	DIN 53363

THERMAL	Nominal value	Unit	Test method
Melting temperature	266	℃	ISO 12086

Electrical performance	Nominal value	Unit	Test method
Dielectric strength
0.25 mm	59	kV/mm	ASTM D149
Dielectric constant
23 ℃，1 MHz	2.58		ASTM D150

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	V-0		UL 94
Extreme oxygen index	35	%	ASTM D2863

optical performance	Nominal value	Unit
Refractive index	1.400
Transmittance
100 µm，550 nm	93.0	%

Supplementary information	Nominal value	Unit	Test method
MIT flexural strength (double folds, 200.0 µ m)	40000		ASTM D2176

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel 1 zone temperature	255	°C
Barrel 2 zone temperature	280	°C
Barrel 3 zone temperature	290	°C
Barrel 4 zone temperature	310	°C
Nozzle temperature	320 to 345	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.