NORDEL™ 6530 XFC EPDM

About
NORDEL™ 6530 XFC EPDM is an amorphous EPDM grade designed for extrusion and molded applications that require fast cure conditions and rapid property build. The combination of low viscosity, broad molecular weight distribution, and low crystallinity allows for good balance of processability, low-temperature properties and performance. It is ideally suited for fast extrusion, injection and transfer molded brake parts, corner moldings, general-purpose gaskets, and moldings. The combination of low viscosity and low crystallinity allows for good processability, low temperature properties, and product performance without the addition of a plasticizer. Main Characteristics: Amorphous High diene Low viscosity Good low temperature properties Applications: Injection and transfer molded articles Extruded profiles General purpose gaskets Complies with: U.S. FDA 21 CFR 177.2600 (See Note 1) U.S. FDA 21 CFR 175.105 (See Note 2) Consult the regulations for complete details. NOTES: (1) Can be used in contact with all foods except water in oil emulsions, high or low fat, and low moisture fats and oil. (2) Adhesives only.

About

NORDEL™ 6530 XFC EPDM is an amorphous EPDM grade designed for extrusion and molded applications that require fast cure conditions and rapid property build. The combination of low viscosity, broad molecular weight distribution, and low crystallinity allows for good balance of processability, low-temperature properties and performance. It is ideally suited for fast extrusion, injection and transfer molded brake parts, corner moldings, general-purpose gaskets, and moldings. The combination of low viscosity and low crystallinity allows for good processability, low temperature properties, and product performance without the addition of a plasticizer. Main Characteristics: Amorphous High diene Low viscosity Good low temperature properties Applications: Injection and transfer molded articles Extruded profiles General purpose gaskets Complies with: U.S. FDA 21 CFR 177.2600 (See Note 1) U.S. FDA 21 CFR 175.105 (See Note 2) Consult the regulations for complete details. NOTES: (1) Can be used in contact with all foods except water in oil emulsions, high or low fat, and low moisture fats and oil. (2) Adhesives only.

Product Description
Supplier	DOW
Generic	三元乙丙橡胶
Material Status	Commercial: Active
Availabilitys	North America,Latin America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.860	g/cm³	ASTM D297
Mooney viscosity (ML 1+4125 ° C)	30	MU	ASTM D1646
Ethylene composition	55.0	wt%	ASTM D3900
Ethylidene norbornene content	8.5	wt%	ASTM D6047
Propylene content	36.5	wt%	ASTM D3900
Residual conversion metal	< 10	ppm	Internal Method
molecular weight distribution	Broad		Internal Method
Ash Content	< 0.1	%	ASTM D296
Volatiles	< 0.40	wt%	Internal Method

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.