Ultramid® A 20 V25 NATURAL

About
TECHNYL® A 20 V25 Natural is a Red Phosphorous flame retardant polyamide 66, reinforced with 25% of glass fiber, heat stabilized, for injection moulding. This grade provides robust UL 94 V-0 and a full UL yellow card while offering good mechanical properties. This grade is suitable for moulding insulating parts for electrical devices, and more generally for thin parts under stress.&&

Product Description
Supplier	BASF
Generic	PA66
Material Status	Commercial: Active
Features	Flame Characteristics,Heat Stabilized,V-0
Availabilitys	Europe,Asia Pacific,North America,Africa & Middle East ,Latin America
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.38	g/cm³	ISO 1183/A
Water absorption
Equilibrium, 23 ℃, 50% RH	2.1	%	ISO 62
23℃，24hr	0.75	%	ISO 62
Molding shrinkage
Parallel	0.35	%
Vertical normal	1.2	%

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
23 ℃, dry	9400	MPa	ISO 527-2/1A
	6300	MPa	ISO 527-2/1A
Tensile Strength
Break, 23 ℃, dry dry	150	MPa	ISO 527-2/1A
Break, 23 ℃, wet cond	100	MPa	ISO 527-2/1A
Tensile Strain
Fracture, 23 ℃, dry dry	2.5	%	ISO 527-2
Fracture, 23 ℃, wet cond	5.2	%	ISO 527-2
Flexural modulus
23 ℃, dry	8500	MPa	ISO 178
23 ℃, moist cond	5700	MPa	ISO 178
Flexural strength
23 ℃, dry	255	MPa	ISO 178
23 ℃, moist cond	170	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy notched impact strength
-30 ℃, dry	7.0	kJ/m²	ISO 179/1eA
23 ℃, dry	8.0	kJ/m²	ISO 179/1eA
23 ℃, moist cond	9.0	kJ/m²	ISO 179/1eA
Charpy impact strength of simply supported beams			ISO 179/1eU
-30 ℃, dry	50	kJ/m²	ISO 179/1eU
23 ℃, dry	55	kJ/m²	ISO 179/1eU
23 ℃, moist cond	60	kJ/m²	ISO 179/1eU
Izod notched impact strength
23 ℃, dry	8.0	kJ/m²	ISO 180/1A
23 ℃, moist cond	9.0	KJ/m²	ISO 180/1A

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature HDT
1.8 MPa, unannealed	244	℃	ISO 75-2/-1
Melting temperature	263	℃	ISO 11357-1/-3

ELECTRICAL	Nominal value	Unit	Test method
Surface resistivity
Dry	1E13	ohms	IEC 62631-3-2
Wet Cond	1E12	ohms	IEC 62631-3-2
Volume resistivity
Dry	1E13	ohm·m	IEC 62631-3-1
Wet Cond	1E11	ohm·m	IEC 62631-3-1
Electric strength
0.8 mm	30	kV/mm	IEC 60243-1
Relative permittivity
Dry, 100Hz	3.4		IEC 62631-2-1
Wet Cond, 100Hz	4		IEC 62631-2-1

Dry	0.02	E-4	IEC 62631-2-1
Wet Cond	0.05	E-4	IEC 62631-2-1
Compared tracking index
Solution A	400		IEC 60112

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level			UL 94
0.80 mm	V-0	calss	UL 94
1.60 mm	V-0	calss	UL 94
3.20 mm	V-0	calss	UL 94
Glow Wire Flammability Index			IEC 60695-2-12
0.80 mm	960	℃	IEC 60695-2-12
1.6 mm	960	℃	IEC 60695-2-12
3.2 mm	960	℃	IEC 60695-2-12

1.6 mm	725	℃	IEC 60695-2-13
	31	%	ISO 4589-2
French Fire Index	F3		NF F16-101
French Smoke Index	I3		NF F16-101

Process Conditions
Injection molding	Nominal value	Unit	Test method
Drying Temperature	80	°C
Recommended maximum water content	0.20	%
Injection molding cylinder temperature 1	265 to 275	°C
Injection molding cylinder temperature 2	270 to 280	°C
Injection molding cylinder temperature 3	280 to 290	°C
Mold temperature	60 to 90	°C	ISO 294

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.