| About |
|---|
| Data generated in BOZ labs. High heat grade for nonchemical resistance required applications.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PC+PET |
| Material Status | Commercial: Active |
| Features | High Heat Resistance |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 | g/cm³ | ASTM D792 |
| Melt Volume Rate | |||
| 265℃，1.2 kg | 4.00 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| TD | 0.50 to 0.80 | % | Internal Method |
| MD | 0.50 to 0.80 | % | Internal Method |
| Water absorption rate | ASTM D570 | ||
| 24hr | 0.10 | % | ASTM D570 |
| Equilibrium, 23 ℃ | 0.70 | % | ASTM D570 |
| Balance, 50% RH | 0.20 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2100 | MPa | ASTM D638 |
| tensile strength | |||
| fracture | 50.0 | MPa | ASTM D638 |
| fracture | 40.0 | MPa | ISO 527-2/50 |
| yield | 55.0 | MPa | ISO 527-2/50 |
| yield | 50.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 110 | % | ASTM D638 |
| fracture | 70 | % | ISO 527-2/50 |
| yield | 5.0 | % | ASTM D638 |
| yield | 5.0 | % | ISO 527-2/50 |
| Bending modulus | 2200 | MPa | ISO 178 |
| 50 mm span | 2100 | MPa | ASTM D790 |
| bending strength | 80.0 | MPa | ISO 178 |
| bending strength | |||
| Yield, 50 mm span | 94.5 | MPa | ASTM D790 |
| Poisson’s ratio | 0.40 | ASTM D638 | |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 16.0 | mg | ASTM D1044 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 35 | kJ/m² | ISO 179/1eA |
| 23℃ | 45 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | No Break | ISO 179/1eU | |
| 23℃ | No Break | ISO 179/1eU | |
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -40℃ | 220 | J/m | ASTM D256 |
| -30℃ | 250 | J/m | ASTM D256 |
| -20℃ | 600 | J/m | ASTM D256 |
| 0℃ | 670 | J/m | ASTM D256 |
| 23℃ | 700 | J/m | ASTM D256 |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -40℃ | 15 | kJ/m² | ISO 180-1A |
| -30℃ | 25 | kJ/m² | ISO 180-1A |
| -20℃ | 35 | kJ/m² | ISO 180-1A |
| -10℃ | 38 | kJ/m² | ISO 180-1A |
| 23℃ | 40 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | ISO 180/1U | ||
| -30℃ | No Break | ISO 180/1U | |
| 23℃ | No Break | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 100 mm span | 105 | ℃ | ISO 75-2/Ae |
| 0.45 MPa, unannealed, 100 mm span | 125 | ℃ | ISO 75-2/Be |
| Vicat Softening Temp | |||
| A50 | 140 | ℃ | ISO 306/A50 |
| B50 | 130 | ℃ | ISO 306 |
| B120 | 135 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | |||
| TD：-30~30℃ | 7.9E-5 | 1/℃ | ASTM D696 |
| MD：-30~30℃ | 7.6E-5 | 1/℃ | ASTM D696 |
| Thermal conductivity coefficient | 0.18 | W/m/K | ASTM C177 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | ASTM D257 |
| Volume resistivity | > 1.0E+14 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 3.2 mm in oil | 17 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 50 Hz | 3.30 | ASTM D150 | |
| 60 Hz | 3.30 | ASTM D150 | |
| 1 MHz | 3.10 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 50 Hz | 2.0E-3 | ASTM D150 | |
| 60 Hz | 2.0E-3 | ASTM D150 | |
| 1 MHz | 0.020 | ASTM D150 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 110 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Drying time, maximum | 8.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Recommended injection volume | 50 to 80 | % | |
| Barrel rear temperature | 243 to 266 | °C | |
| Barrel middle temperature | 249 to 271 | °C | |
| Barrel front temperature | 254 to 277 | °C | |
| Nozzle temperature | 254 to 271 | °C | |
| Processing (melt) temperature | 260 to 277 | °C | |
| Mold temperature | 66 to 88 | °C | |
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw speed | 50 to 80 | rpm | |
| Vent depth | 0.013 to 0.020 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tensile Bar |
| 3. 2.0 in/min |
| 4. Type I, 2.0 in/min |
| 5. 0.051 in/min |
| 6. 0.079 in/min |
| 7. Yield |
| 8. 80*10*4 sp=62mm |
| 9. 80*10*4 |
| 10. 120*10*4 mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |