| About |
|---|
| Pebax® Rnew® 55R53 SP 01 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide based on renewable resources. This SP grade has been developed to be heat and UV resistant. The percentage of renewable carbon according to ASTM D 6866 is 62-66%.&& |
| Product Description | |
|---|---|
| Supplier | Arkema |
| Generic | PA12弹性体 |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Renewable resources,High Heat Resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.03 | g/cm³ | ISO 1183 |
| Shrinkage rate | Internal Method | ||
| TD：4.0 mm，24 hrs | 1.0 | % | Internal Method |
| MD：4.0 mm，24 hrs | 1.0 | % | Internal Method |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.70 | % | ISO 62 |
| 23℃，24hr | 1.5 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ISO 868 | ||
| Shaw’s D | 53 | ISO 868 | |
| Shore D, 15 seconds | 51 | ISO 868 | |
| tensile strength | |||
| fracture | 45.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | > 400 | % | ISO 527-2 |
| Bending modulus | 160 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179 | ||
| -30℃ | No Break | ISO 179 | |
| 23℃ | No Break | ISO 179 | |
| Charpy Unnotch Impact strength | ISO 179 | ||
| -30℃ | No Break | ISO 179 | |
| 23℃ | No Break | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 156 | ℃ | ISO 306 |
| Melting temperature | 167 | ℃ | ISO 11357-3 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Renewable Carbon Conent | 62 to 66 | % | ASTM D6866 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 65 to 75 | °C | |
| Drying time | 4.0 to 8.0 | hr | |
| Processing (melt) temperature | 200 to 270 | °C | |
| Mold temperature | 25 to 60 | °C | |
| Drying temperature | 65 to 75 | °C | |
| Drying time | 4.0 to 8.0 | hr | |
| Melt temperature | 210 to 230 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |