| About |
|---|
| ULTEM™ 1010TC resin is an amorphous, transparent polyetherimide (PEI) plastic offering a glass transition temperature (Tg) of 217°C, with UL94 V0 and 5VA ratings offering high heat resistance and infrared transmission.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polyetherimide |
| Material Status | Commercial: Active |
| Features | High Heat Resistance,Amorphous,V-0,5VA |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.27 | g/cm³ | ASTM D792, ISO 1183 |
| Melt Flow Rate | |||
| 337℃，6.60kg | 18 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 220℃，5 kg | 25.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.50 to 0.70 | % | Internal Method |
| Water absorption rate | |||
| 24hr | 0.25 | % | ASTM D570 |
| Saturation, 23 ℃ | 1.3 | % | ISO 62 |
| Equilibrium, 23 ℃ | 1.3 | % | ASTM D570 |
| Equilibrium, 23 ℃, 50% RH | 0.70 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 3.0 | kJ/m² | ISO 179/1eA |
| Notched impact strength of cantilever beam | |||
| 23℃ | 1300 | J/m | ASTM D4812 |
| Impact strength of cantilever beam notch | |||
| 3.2mm | 1200 | J/m | ASTM D256 |
| Dart impact equipped with measuring instruments | |||
| 23℃，Total Energy | 33.0 | J | ASTM D3763 |
| Drop hammer impact | |||
| 23℃ | 33.0 | J | ASTM D3029 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 6.4 mm | 207 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.4 mm | 198 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 64 mm span | 193 | ℃ | ISO 75-2/Af |
| Vicat Softening Temp | |||
| — | 218 | ℃ | ASTM D1525 14 |
| B50 | 211 | ℃ | ISO 306 |
| B120 | 212 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | |||
| MD：-20~150℃ | 5.6E-5 | 1/℃ | ASTM E831 |
| MD：-40~40℃ | 5.0E-5 | 1/℃ | ISO 11359-2 |
| TD：-40~40℃ | 5.0E-5 | 1/℃ | ASTM E831，ISO 11359-2 |
| Thermal conductivity coefficient | 0.22 | W/m/K | ASTM C177 |
| Relative temperature index | 170 | ℃ | UL 746 |
| Electrical performance | 170 | ℃ | UL 746 |
| Impact mechanical performance | 170 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | ASTM D149 | ||
| 1.6 mm in air | 33 | kV/mm | |
| 1.6 mm in oil | 28 | kV/mm | |
| Dielectric constant | |||
| 1 kHz | 3.15 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 1 kHz | 1.3E-3 | ||
| 2.45 GHz | 2.5E-3 | ||
| Arc resistance | PLC 5 | ASTM D495 | |
| Compared to the leakage tracing index | PLC 4 | UL 746 | |
| High Arc Burning Index (HAI) | PLC 3 | UL 746 | |
| High voltage arc marking rate | |||
| HVTR | PLC 2 | UL 746 | |
| Hot wire ignition | |||
| HWI | PLC 1 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.50 mm | V-0 | ||
| 3.00 mm | 5VA | ||
| Extreme oxygen index | 44 | % | ASTM D2863 |
| NBS smoke density | |||
| Flaming，Ds，4 min | 2.00 | ASTM E662 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 109 | ASTM D785 | |
| Tensile modulus | |||
| — | 3590 | MPa | ASTM D638 |
| — | 3200 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 110 | MPa | ASTM D638 |
| yield | 105 | MPa | ISO 527-2/5 |
| fracture | 105 | MPa | ASTM D638 |
| fracture | 85.0 | MPa | ISO 527-2/5 |
| Tensile strain | |||
| yield | 7.0 | % | ASTM D638 |
| yield | 6.0 | % | ISO 527-2/5 |
| fracture | 60 | % | ASTM D638 |
| fracture | 60 | % | ISO 527-2/5 |
| Bending modulus | |||
| 50 mm span | 3420 | MPa | ASTM D790 |
| — | 3300 | MPa | ISO 178 |
| bending strength | |||
| — | 160 | MPa | ISO 178 |
| Yield, 50 mm span | 174 | MPa | ASTM D790 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 10.0 | mg | ASTM D1044 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 149 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Drying time, maximum | 24 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |