POLYFLON™ M-15

About
Daikin PTFE (polytetrafluoroethylene) molding powders are excellent, fine cut resins, well suited for a variety of demanding chemical, mechanical, electrical and non-stick surface applications. These PTFE resins are fully fluorinated and have the best thermal, electrical, and chemical properties of all fluoropolymers with a continuous service rating of 500°F (260°C). Daikin PTFE molding powders are available in homopolymer and modified fine cut grades. Daikin PTFE molding powders can be used continuously at temperatures up to 260°C (500°F) and for short periods of time at higher temperatures. They also possess excellent low temperature strength. Daikin PTFE molding powders are completely inert to attack by all chemicals except hightemperature, high-pressure elemental fluorine gas, molten alkaline metals and chlorine trifluoride. The non-polar molecular structure makes Daikin PTFE molding powders ideal for use as high-frequency insulating material. The dielectric constant and dissipation factor are uniformly low over a wide frequency range. Under ordinary conditions of use, Daikin PTFE molding powders possess the lowest coefficient of friction of any solid material. Also, the non-stick properties of these products prevent most materials from adhering to them. Chemical/Mechanical—Packings, gaskets, diaphragms, bellows, corrosion-resistant linings, piping components, pump parts, O-rings, V-rings, bushings, slide bearings, etc. Electrical/Other—Insulating skived tape, insulating sleeves, terminals, connectors, sockets, spacers, electronic parts, laboratory equipment, etc.&&

About

Daikin PTFE (polytetrafluoroethylene) molding powders are excellent, fine cut resins, well suited for a variety of demanding chemical, mechanical, electrical and non-stick surface applications. These PTFE resins are fully fluorinated and have the best thermal, electrical, and chemical properties of all fluoropolymers with a continuous service rating of 500°F (260°C). Daikin PTFE molding powders are available in homopolymer and modified fine cut grades. Daikin PTFE molding powders can be used continuously at temperatures up to 260°C (500°F) and for short periods of time at higher temperatures. They also possess excellent low temperature strength. Daikin PTFE molding powders are completely inert to attack by all chemicals except hightemperature, high-pressure elemental fluorine gas, molten alkaline metals and chlorine trifluoride. The non-polar molecular structure makes Daikin PTFE molding powders ideal for use as high-frequency insulating material. The dielectric constant and dissipation factor are uniformly low over a wide frequency range. Under ordinary conditions of use, Daikin PTFE molding powders possess the lowest coefficient of friction of any solid material. Also, the non-stick properties of these products prevent most materials from adhering to them. Chemical/Mechanical—Packings, gaskets, diaphragms, bellows, corrosion-resistant linings, piping components, pump parts, O-rings, V-rings, bushings, slide bearings, etc. Electrical/Other—Insulating skived tape, insulating sleeves, terminals, connectors, sockets, spacers, electronic parts, laboratory equipment, etc.&&

Product Description
Supplier	Daikin Fluorochemicals
Generic	PTFE
Material Status	Commercial: Active
Features	No viscosity,High Viscosity,Low coefficient of friction,High molecular weight,Solvent resistance,Low temperature strength,Homopolymer
Availabilitys	North America
Process Methods	sintering

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	2.16	g/cm³	ASTM D4894
Apparent density	0.47	g/cm³	ASTM D4894
Shrinkage rate
MD	4.1	%	Internal Method

MECHANICAL	Nominal value	Unit	Test method
tensile strength
Yield, 1.50 mm	43.0	MPa	ASTM D4894
Tensile strain
Fracture, 1.50 mm	400	%	ASTM D4894
compressive strength			ASTM D695
0% strain	7.80	MPa	ASTM D695
1% strain	5.00	MPa	ASTM D695
25% strain	28.1	MPa	ASTM D695
Load deformation			ASTM D621
25℃，14 MPa	17.2	%	ASTM D621
100℃，14 MPa	33.3	%	ASTM D621
200℃，6.9 MPa	27.0	%	ASTM D621

elastic body	Nominal value	Unit	Test method
Compression deformation			ASTM D621
25℃	8.6	%	ASTM D621
100℃	20	%	ASTM D621
200℃	16	%	ASTM D621

THERMAL	Nominal value	Unit	Test method
Continuous use temperature	260	℃
Melting temperature	327	℃	DSC

Electrical performance	Nominal value	Unit	Test method
Surface resistivity	> 1.0E+15	ohms	ASTM D257
Volume resistivity	> 1.0E+18	ohms·cm	ASTM D257
Dielectric strength	100	kV/mm
Dielectric constant
1 kHz	< 2.10		ASTM D150
Dissipation factor
1 kHz	< 1.0E-4		ASTM D150

Supplementary information	Nominal value	Unit	Test method
MIT flexural strength	5.00E+6		ASTM D2178
Stretching Void Index	300		ASTM D4895

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.