| About |
|---|
| TECHNYL eXten® D 219CR V33 Natural is a grade based on polyamide blend of polyamide 6.10 and polyamide 66, reinforced with 33% of glass fiber, heat stabilized with organic stabilizers, for injection moulding.&& |
| Product Description | |
|---|---|
| Supplier | DOMO |
| Generic | PA 66/610 |
| Material Status | Commercial: Negative |
| Features | Good liquidity,Hydrolysis stability,Low moisture absorption,Solvent resistance,Ultra High Glycol Resistance,Good surface appearance,Welding,Good Dimensional Stability,Road Salt Resistant,Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.35 | g/cm³ | ISO 1183/A |
| Water absorption rate | ISO 62 | ||
| 23℃，24hr | 0.30 | % | ISO 62 |
| Saturation, 23 ℃ | 3.6 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 1.3 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 11000 | MPa | ISO 527-2/1A |
| tensile strength | |||
| Fracture, 23 ℃ | — | MPa | ASTM D638 |
| Fracture, 23 ℃ | 190 | MPa | ISO 527-2/1A |
| Tensile strain | |||
| Fracture, 23 ℃ | 3.1 | % | ASTM D638 |
| Fracture, 23 ℃ | 3.0 | % | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 9900 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 285 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 10 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 85 | kJ/m² | ISO 179/1eU |
| Impact strength of cantilever beam notch | |||
| 23℃ | 10 | kJ/m² | ISO 180 |
| Notched impact strength of cantilever beam | |||
| 23℃ | 100 | kJ/m² | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 223 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, unannealed | 215 | ℃ | ISO 75-2/Af |
| Melting temperature | 220 to 260 | ℃ | ISO 11357-3 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |