| About |
|---|
| Antisqueak Blow Molding Grade&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | TPC-ET |
| Material Status | Commercial: Active |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.15 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 230℃，10 kg | 6.50 | cm³/10min | ISO 1133 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.70 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.30 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore D, 3 seconds | 37 | ISO 868 | |
| Tensile modulus | 65.0 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| fracture | 32.0 | MPa | ISO 527-2 |
| fracture | 21.0 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| 5% strain | 3.50 | MPa | ISO 527-2 |
| 5% strain | 3.40 | MPa | ISO 527-2 |
| 10% strain | 5.70 | MPa | ISO 527-2 |
| 10% strain | 5.40 | MPa | ISO 527-2 |
| 10% strain | 6.00 | MPa | ISO 527-2 |
| 10% strain, 100 ℃ | 2.60 | MPa | ISO 527-2 |
| 50% strain | 11.2 | MPa | ISO 527-2 |
| 50% strain | 8.70 | MPa | ISO 527-2 |
| 100% strain | 9.30 | MPa | ISO 527-2 |
| 100% strain | 14.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 960 | % | ISO 527-2 |
| Tensile strain | |||
| fracture | 280 | % | ISO 527-2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | No Break | ISO 179/1eA | |
| 23℃ | No Break | ISO 179/1eA | |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -20℃ | No Break | ISO 180/1A | |
| 23℃ | No Break | ISO 180/1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 214 | ℃ | ISO 11357-3 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| tear strength | |||
| without nick，normal | 265 | MPa | ISO 34 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die Cutting – Normal |
| 3. Die Cutting – Parallel |
| 4. Method Ba, Angle (Unnicked) |
| 5. Die Cutting |
| 6. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |