| About |
|---|
| Amodel® AFA-6133 V0 Z is a 33% glass-fiber reinforced, flame retardant grade of polyphthalamide (PPA) resin specifically formulated for connector applications requiring compatibility with both infrared and vapor phase soldering operations typically used by the electronics industry. Amodel® AFA-6133 V0 Z offers high flow and short molding cycles, thereby enhancing molding productivity and lowering costs. Black: AFA-6133 V0 Z BK 324&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | PPA |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Dimensional Stability,High liquidity,Good Electrical Properties,Flame Characteristics,Solvent resistance,V-0 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.68 | g/cm³ | ISO 1183/A |
| Shrinkage rate | |||
| TD | 0.60 | % | ASTM D955 |
| MD | 0.30 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 0.20 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 16100 | MPa | ASTM D638 |
| Tensile modulus | ISO 527-2 | ||
| 23℃ | 14500 | MPa | ISO 527-2 |
| 100℃ | 9170 | MPa | ISO 527-2 |
| 150℃ | 5930 | MPa | ISO 527-2 |
| 175℃ | 5100 | MPa | ISO 527-2 |
| tensile strength | 199 | MPa | ASTM D638 |
| tensile strength | ISO 527-2 | ||
| Yield, 23 ℃ | 186 | MPa | ISO 527-2 |
| Yield, 100 ℃ | 114 | MPa | ISO 527-2 |
| Yield, 150 ℃ | 75.2 | MPa | ISO 527-2 |
| Yield, 175 ℃ | 63.4 | MPa | ISO 527-2 |
| Tensile strain | ISO 527-2 | ||
| fracture | 1.7 | % | ASTM D638 |
| Fracture, 23 ℃ | 1.6 | % | ISO 527-2 |
| Fracture, 24 ℃ | 2.4 | % | ISO 527-2 |
| Fracture, 150 ℃ | 5.1 | % | ISO 527-2 |
| Fracture, 175 ℃ | 4.9 | % | ISO 527-2 |
| Bending modulus | 13100 | MPa | ASTM D790 |
| Bending modulus | ISO 178 | ||
| 23℃ | 12600 | MPa | ISO 178 |
| 100℃ | 8070 | MPa | ISO 178 |
| 150℃ | 4960 | MPa | ISO 178 |
| 175℃ | 4620 | MPa | ISO 178 |
| bending strength | 224 | MPa | ASTM D790 |
| bending strength | ISO 178 | ||
| 23℃ | 259 | MPa | ISO 178 |
| 100℃ | 161 | MPa | ISO 178 |
| 150℃ | 101 | MPa | ISO 178 |
| 175℃ | 87.6 | MPa | ISO 178 |
| compressive strength | 145 | MPa | ASTM D695 |
| shear strength | 80.0 | MPa | ASTM D732 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 14 | kJ/m² | ISO 179/1eA |
| 23℃ | — | kJ/m² | ISO 179/2eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 46 | kJ/m² | ISO 179/1eU |
| Impact strength of cantilever beam notch | 85 | J/m | ASTM D256 |
| 23℃ | 8.2 | kJ/m² | ISO 180-1A |
| Impact strength of cantilever beam notch | 690 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 23℃ | 44 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 277 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 282 | ℃ | ISO 75-2/Af |
| Melting peak temperature | 310 | ℃ | ASTM D3418 |
| Melting temperature | 310 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| TD | ASTM E831 | ||
| MD | ASTM E831 | ||
| 0 to 100 ℃ | 1.7E-5 | cm/cm/℃ | ASTM E831 |
| 100 to 200 ℃ | 7.0E-6 | cm/cm/℃ | ASTM E831 |
| 0 to 100 ℃ | 6.4E-5 | cm/cm/℃ | ASTM E831 |
| 100 to 200 ℃ | 1.1E-4 | cm/cm/℃ | ASTM E831 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+15 | ohms | ASTM D257 |
| Volume resistivity | 1.0E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 3.18 mm | 24 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 100 Hz | 4.40 | ASTM D150 | |
| 1 MHz | 4.10 | ASTM D150 | |
| Dissipation factor | |||
| 1 MHz | 0.011 | ASTM D150 | |
| Compared to the leakage tracing index | PLC 1 | UL 746 | |
| High Arc Burning Index (HAI) | UL 746 | ||
| 0.75 mm | PLC 0 | UL 746 | |
| 1.5 mm | PLC 0 | UL 746 | |
| 3.0 mm | PLC 0 | UL 746 | |
| Hot wire ignition | |||
| HWI | UL 746 | ||
| 0.75 mm | PLC 0 | UL 746 | |
| 1.5 mm | PLC 0 | UL 746 | |
| 3.0 mm | PLC 0 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.80 mm | V-0 | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | < 120 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.030 to 0.060 | % | |
| Barrel rear temperature | 327 to 332 | °C | |
| Barrel middle temperature | 316 to 324 | °C | |
| Barrel front temperature | 316 to 324 | °C | |
| Processing (melt) temperature | 321 to 338 | °C | |
| Mold temperature | 66 to 93 | °C | |
| Notes |
|---|
| 1. Restricted Approval as noted in GM MATSPC |
| 2. Typical properties: these are not to be construed as specifications. |
| 3. This flammability rating is not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |