| About |
|---|
| ARLEN™ G335 is a Polyamide 6T (Nylon 6T) material filled with 35% glass fiber. It is available in North America. Primary attribute of ARLEN™ G335: Flame Rated.&& |
| Product Description | |
|---|---|
| Supplier | Mitsui |
| Generic | PA 6T |
| Material Status | Commercial: Active |
| Features | HB |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.47 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| TD：2.0 mm | 0.50 | % | ASTM D955 |
| MD：2.0 mm | 0.20 | % | ASTM D955 |
| Water absorption rate | ASTM D570 | ||
| 23℃，24hr | 0.30 | % | ASTM D570 |
| 100℃，24hr | 1.7 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | 200 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 3.0 | % | ASTM D638 |
| Bending modulus | 11000 | MPa | ASTM D790 |
| bending strength | 340 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 100 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 280 | ℃ | ASTM D648 |
| Glass transition temperature | 140 | ℃ | DSC |
| Melting temperature | 300 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | 28 | kV/mm | ASTM D149 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 110 | °C | |
| Drying time | 2.0 to 6.0 | hr | |
| Hopper temperature | 50 to 90 | °C | |
| Barrel rear temperature | 315 to 330 | °C | |
| Barrel middle temperature | 320 to 335 | °C | |
| Barrel front temperature | 325 to 340 | °C | |
| Nozzle temperature | 325 to 340 | °C | |
| Mold temperature | 90 to 140 | °C | |
| Injection speed | Moderate | ||
| Screw speed | 150 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |