| About |
|---|
| TECATRON™ PPS is a high performance thermoplastic that combines good mechanical properties with excellent thermal and chemical resistance properties. There is no known solvent that dissolves TECATRON™ PPS at temperatures below 392°F. Its low ionic impurities make it an excellent choice for applications where high purity is a concern. TECATRON™ GF40 is a glass reinforced material that offers extremely high strength along with excellent chemical resistance properties. TECATRON™ PVX is a bearing grade PPS that is suitable for high load applications. TECATRON™PPS’s excellent thermal and chemical resistance along with its ionic impurities make an excellent choice for applications requiring low outgassing and high purity. TECATRON™PPS is typically used in the automotive, electrical/ electronic, industrial, mechanical, appliance and semiconductor industries. High purity characteristics Outstanding retention of mechanical properties under continuous use up to 338°F (170°C) Excellent chemical resistance Good electrical insulator High mechanical strength High strength-to-weight ratio Corrosion resistant Dimensional stability over wide variations of temperature and moisture Creep resistance&& |
| Product Description | |
|---|---|
| Supplier | Ensinger |
| Generic | PPS |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good flexibility,High purity,Good Dimensional Stability,Low (to None) Ion Content,Corrosion Resistant,Solvent resistance,Insulation,V-0 |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.35 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 23℃，24hr | 0.020 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 27 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed | 204 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 104 | ℃ | ASTM D648 |
| Melting temperature | 282 | ℃ | ASTM D2133 |
| Linear coefficient of thermal expansion | |||
| MD | 7.2E-5 | 1/℃ | ASTM D696 |
| Thermal conductivity coefficient | 0.30 | W/m/K | |
| Maximum operating temperature | |||
| long-term | 170 | ℃ | UL 746B |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm | ASTM D257 |
| Dielectric constant | |||
| 23 ℃，60 Hz | 3.00 | ASTM D150 | |
| Dissipation factor | |||
| 23℃，60 Hz | 1.0E-4 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 104 | ASTM D785 | |
| Tensile modulus | 3310 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 23 ℃ | 60.0 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 4.0 | % | ASTM D638 |
| Bending modulus | |||
| 23℃ | 3000 | MPa | ASTM D790 |
| bending strength | |||
| 23℃ | 120 | MPa | ASTM D790 |
| friction coefficient | |||
| With oneself – dynamic | 0.24 | ASTM D1894 | |
| Wear factor | |||
| 0.28 MPa，0.25 m/sec | 1100 | 10^-8 mm³/N·m | ASTM D3702 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 40 psi, 50 fpm |
| 3. 50% RH |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |