| About |
|---|
| Grivory® HT2V-3X V0 nat 6059 is a Polyamide 6T/66 Copolymer (Nylon 6T/66) material filled with 30% glass fiber. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding. Important attributes of Grivory® HT2V-3X V0 nat 6059 are: Flame Rated Flame Retardant Chemical Resistant Good Mold Release Heat Resistant Typical applications include: Automotive Electrical/Electronic Applications Appliances Engineering/Industrial Parts Lighting Applications&& |
| Product Description | |
|---|---|
| Supplier | EMS-GRIVORY |
| Generic | PA 6T/66 |
| Material Status | Commercial: Active |
| Features | Ethanol tolerance,Good liquidity,Aromatic,Good stripping performance,Flame Characteristics,High Heat Resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.43 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD | 0.10 | % | ISO 294-4 |
| TD | 0.90 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | 3.5 | % | ISO 62 |
| 23℃，50% RH | 1.3 | % | ISO 62 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 280 | ℃ | ISO 75-2/Af |
| Melting temperature | 310 | ℃ | ISO 11357-3 |
| Vicat Softening Temp | |||
| Linear coefficient of thermal expansion | |||
| MD | 2.5E-5 | 1/℃ | ISO 11359-2 |
| TD | 4.5E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+12 | Ω.cm | IEC 60093 |
| Insulation strength | |||
| 34 | KV/mm | IEC 60243-1 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.35mm | V-0 | UL 94 | |
| 0.75mm | V-0 | UL 94 | |
| 1.00mm | V-0 | UL 94 | |
| 1.40mm | V-0 | UL 94 | |
| 1.50mm | V-0 | UL 94 | |
| 2.00mm | V-0 | UL 94 | |
| Extreme oxygen index | 35 | % | ISO 4589-2 |
| Igniting temperature of the hot wire | |||
| 1 mm | 775 | ℃ | IEC 60695-2-12 |
| 1.5 mm | 775 | ℃ | IEC 60695-2-12 |
| 2 mm | 825 | ℃ | IEC 60695-2-12 |
| 3 mm | 850 | ℃ | IEC 60695-2-12 |
| Relative temperature of heating wire | |||
| 1.00mm | 960 | ℃ | IEC 60695-2-13 |
| 1.50mm | 960 | ℃ | IEC 60695-2-13 |
| 2.00mm | 960 | ℃ | IEC 60695-2-13 |
| 3.00mm | 960 | ℃ | IEC 60695-2-13 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 40 | kJ/m² | ISO 179/1eU |
| -30℃ | 35 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 7.0 | kJ/m² | ISO 179/1eA |
| -30℃ | 6.0 | kJ/m² | ISO 179/1eA |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | 240 | MPa | ISO 2039-1 |
| tensile strength | |||
| 23℃ | 140 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 2.0 | % | ISO 527-2 |
| Tensile modulus | |||
| 23℃ | 10500 | MPa | ISO 527-2 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80.0 | °C | |
| Drying time | 4.0 | Hr | |
| Water content | 0.15 | % | |
| Injection temperature | |||
| Rear barrel temperature | 290 | °C | |
| Central temperature of the barrel | 290 | °C | |
| Barrel front temperature | 290 | °C | |
| Die temperature | 290 | °C | |
| Mold temperature | 80-90 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Long Term |
| 3. Short Term |
| 4. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |