| About |
|---|
| M40060 is High Density Polyethylene grade with narrow molecular weight distribution suitable for injection molding applications. It has been designed to give good rigidity, excellent toughness and low warpage. M40060 is also available with UV stabilizer as M40060S. M40060 series grades are recommended for industrial pails, shipping containers and other parts requiring balance of toughness and rigidity.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | HDPE |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Weather resistance is good,Low warping,Good flexibility,Food contact compliance,Weight distribution |
| Availabilitys | North America,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.960 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 4.0 | g/10min | ASTM D1238 |
| ESCR(Environmental Stress Cracking Resistance) | ASTM D1693B | ||
| 10% non-ionic detergent, molded, F50 | 3.00 | hr | ASTM D1693B |
| 100% non-ionic detergent, molded, F50 | 6.00 | hr | ASTM D1693B |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| Injection molding | 180 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | < -75.0 | ℃ | ASTM D746 |
| Vicat Softening Temp | 125 | ℃ | ASTM D1525 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D, injection molding | 60 | ASTM D2240 | |
| Tensile modulus | |||
| 1% cut, injection molding | 950 | MPa | ASTM D638 |
| tensile strength | ASTM D638 | ||
| Yield, injection molding | 24.0 | MPa | ASTM D638 |
| Fracture, injection molding | 22.0 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, injection molding | > 600 | % | ASTM D638 |
| Bending modulus | |||
| injection molding | 900 | MPa | ASTM D790 |
| bending strength | |||
| injection molding | 24.0 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 232 to 260 | °C | |
| Barrel middle temperature | 232 to 260 | °C | |
| Barrel front temperature | 232 to 260 | °C | |
| Mold temperature | 15 to 60 | °C | |
| Injection pressure | 60.0 to 100 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |