| About |
|---|
| VENYL SE037 – 1731 is a Polyamide 6 (Nylon 6) product. It can be processed by injection molding and is available in Europe. Characteristics include: Flame Rated Eco-Friendly/Green&& |
| Product Description | |
|---|---|
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Renewable resources,HB |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.10 | g/cm³ | ISO 1183 |
| Shrinkage rate | 1.0 to 2.0 | % | |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 2.7 to 2.9 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1700 | MPa | ISO 527-2 |
| tensile strength | |||
| fracture | 45.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 70 | % | ISO 527-2 |
| Bending modulus | 1600 | MPa | ISO 178 |
| bending strength | 130 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | 40 | kJ/m² | ISO 179-1eA |
| Charpy Unnotch Impact strength | No Break | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 70.0 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 155 | ℃ | ISO 75-2/B |
| Melting temperature | |||
| DSC | 220 | ℃ | ISO 3146 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+12 | ohms | DIN 53482 |
| Volume resistivity | 1.0E+15 | ohms·cm | DIN 53482 |
| Compared to the leakage tracing index | |||
| Solution A | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 230 to 240 | °C | |
| Barrel middle temperature | 235 to 240 | °C | |
| Barrel front temperature | 235 to 240 | °C | |
| Nozzle temperature | 220 to 265 | °C | |
| Mold temperature | 45 to 65 | °C | |
| Injection pressure | 70.0 to 90.0 | MPa | |
| Injection speed | Fast | ||
| Hold pressure | 35.0 to 60.0 | MPa | |
| Screw length to diameter ratio | 15.0:1.0 to 20.0:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |