| About |
|---|
| Overview: MAGNUM™ 3525 is a medium heat ABS. Its inherent low gloss combined with a high flow makes it specifically suitable for unpainted interior automotive applications. MAGNUM™ 3525 can thereby help you to save up to 50% of the part costs. It is globally available, locally produced in major car production regions. Benefits: Lot to lot consistency allowing for optimal machine parameters settings from the start Self-coloring enabling improvement of costs by using less pigments and lowering your logistic costs Low VOC allowing a better interior air quality facing increasing regulatory and OEMs constraints. Heat stability during wide range of processing temperatures: enhanced part design freedom High scratch and mar resistance for an improved aesthetic durability of the parts Easier recyclability of unpainted part Applications: Matt/unpainted interior automotive applications Mid-consoles Pillars Door liners Glove boxes&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Generic | ABS |
| Material Status | Commercial: Active |
| Features | Excellent Processability,HB |
| Availabilitys | Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.05 | g/cm³ | ISO 1183/B |
| Apparent density | 0.65 | g/cm³ | ISO 60 |
| Melt Flow Rate | |||
| 220℃，10.0kg | 11 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.40 to 0.70 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 3.20 mm, injection molded | 2200 | MPa | ISO 527-2 |
| tensile strength | |||
| Yield, 3.20 mm, injection molding | 43.0 | MPa | ISO 527-2/50 |
| Yield, 3.20 mm, injection molding | 44.0 | MPa | ISO 527-2/100 |
| Tensile strain | |||
| Yield, 3.20 mm, injection molding | 3.3 | % | ISO 527-2/50 |
| Yield, 3.20 mm, injection molding | 3.3 | % | ISO 527-2/100 |
| Bending modulus | |||
| 3.20 mm, injection molded | 2100 | MPa | ISO 178 |
| bending strength | |||
| 3.20 mm, injection molded | 65.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30 ℃, injection molding | 11 | kJ/m² | ISO 179/1eA |
| -30 ℃, injection molding | 8.0 | kJ/m² | ISO 179/2C |
| 23 ℃, injection molding | 17 | kJ/m² | ISO 179/1eA |
| 23 ℃, injection molding | 12 | kJ/m² | ISO 179/2C |
| Impact strength of cantilever beam notch | ISO 180/A | ||
| -30 ℃, injection molding | 10 | kJ/m² | ISO 180-A |
| 23 ℃, injection molding | 17 | kJ/m² | ISO 180-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 101 | ℃ | ISO 75-2/A |
| 1.8 MPa, unannealed | 78.0 | ℃ | ISO 75-2/A |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Burning rate | |||
| 2.0 mm | 60 | mm/min | ISO 3795 |
| Flame retardant level | UL 94 | ||
| 1.50 mm | HB | UL 94 | |
| 3.00 mm | HB | UL 94 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 3. 3-points |
| 4. This rating not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |