| About |
|---|
| This grade is specialized in toughness and low-flash.&& |
| Product Description | |
|---|---|
| Supplier | TOSOH |
| Generic | PPS |
| Material Status | Commercial: Active |
| Features | Good flexibility,V-0 |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.58 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 315℃，5.0kg | 35 | g/10min | ASTM D1238 |
| Shrinkage rate | Internal Method | ||
| MD | 0.30 | % | Internal Method |
| TD | 0.80 | % | Internal Method |
| Water absorption rate | |||
| balance | < 0.020 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 72 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | 500 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | > 260 | ℃ | ASTM D648 |
| Melting temperature | 285 | ℃ | Internal Method |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | 16 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 1 MHz | 3.90 | ASTM D150 | |
| Dissipation factor | |||
| 1 MHz | 1.4E-3 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Rod flow length | |||
| 1.00 mm | 200 | mm | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 123 | ASTM D785 | |
| tensile strength | 170 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 2.2 | % | ASTM D638 |
| Bending modulus | 12100 | MPa | ASTM D790 |
| bending strength | 261 | MPa | ASTM D790 |
| Tensile Weld Strength | 62.0 | MPa | ASTM D638 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 to 150 | °C | |
| Drying time | 2.0 to 5.0 | hr | |
| Barrel rear temperature | 270 to 300 | °C | |
| Barrel middle temperature | 270 to 300 | °C | |
| Nozzle temperature | 290 to 330 | °C | |
| Mold temperature | 135 to 150 | °C | |
| Injection pressure | 50.0 to 150 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |