| About |
|---|
| A soft, colorable, versatile thermoplastic vulcanizate (TPV) in the thermoplastic elastomer (TPE) family. This material combines good physical properties and chemical resistance for use in a wide range of applications. This grade of Santoprene TPV is shear-dependent and can be processed on conventional thermoplastics equipment for injection molding, extrusion, blow molding, thermoforming or vacuum forming. It is polyolefin based and recyclable within the manufacturing stream.&& |
| Product Description | |
|---|---|
| Supplier | Celanese |
| Material Status | Commercial: Active |
| Features | Low Viscosity,High liquidity,Good Rigidity |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.96 | g/cm³ | ASTM D792 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -60 | ℃ | ASTM D746 |
| Linear coefficient of thermal expansion |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+15 | Ω.cm | ASTM D257 |
| Insulation strength | |||
| 2.03mm | 43 | KV/mm | ASTM D149 |
| Dielectric constant | |||
| 23℃ | 2.30 | 1 kHz | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.00mm | HB | UL-94 | |
| 1.50mm | HB | UL-94 | |
| 3.00mm | HB | UL-94 | |
| Extreme oxygen index | 24 | % | ASTM D2863 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shaw A15s | 86 | ASTM D2240 | |
| tensile strength | |||
| 23℃ | 11.1 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 540 | % | ASTM D638 |
| tear strength | |||
| TD | 35 | KN/m |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| Extrusion molding conditions | Nominal value | Unit | Test method |
| drying temperature | 80 | °C | |
| Drying time | 3 | Hr | |
| Moisture content | 0.08 | % | |
| Injection temperature | |||
| Temperature at the rear of the screw barrel | 175 | °C | |
| Temperature in the middle of the screw barrel | 180 | °C | |
| Front temperature of screw barrel | 180 | °C | |
| Mold head temperature | 190-230 | °C | |
| Mold temperature | 10-50 | °C | |
| drying temperature | 80 | °C | |
| Drying time | 3 | Hr | |
| Mold head temperature | 205 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. Method Bb, Angle (Nicked) |
| 4. Type 1 |
| 5. Type A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |