Durethan® BKV 60 H2.0 EF DUS060 900116

soliao
2024年4月1日
PA6

About
Durethan® BKV60H2.0EF 900116 DUS060 (Dry) PA 6, 60 % glass fibers, injection molding, improved flowability, heat-aging stabilized&&Durethan® BKV60H2.0EF 900116 DUS060 PA 6, 60 % glass fibers, injection molding, improved flowability, heat-aging stabilized&&Durethan® BKV60H2.0EF 900116 DUS060 PA 6, 60 % glass fibers, injection molding, improved flowability, heat-aging stabilized&&

Product Description
Supplier	LANXESS
Generic	PA6
Material Status	Commercial: Active
Features	Good liquidity,Heat Stabilized
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.70	g/cm³	ISO 1183
Apparent density	0.75	g/cm³	ISO 60
Shrinkage rate			ISO 2577
TD：280℃，2.0 mm	0.40	%	ISO 2577
TD：120℃，2.0 mm，4 hrs	0.060	%	ISO 2577
MD：280℃，2.0 mm	0.32	%	ISO 2577
MD：120℃，2.0 mm，4 hrs	0.030	%	ISO 2577
Water absorption rate
Saturation, 23 ℃	3.6	%	ISO 62
Equilibrium, 23 ℃, 50% RH	1.3	%	ISO 62

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179/1eA
-30℃	16	kJ/m²	ISO 179/1eA
23℃	16	kJ/m²	ISO 179/1eA
Charpy Unnotch Impact strength			ISO 179/1eU
-30℃	90	kJ/m²	ISO 179/1eU
23℃	90	kJ/m²	ISO 179/1eU
Impact strength of cantilever beam notch			ISO 180/1A
-30℃	16	kJ/m²	ISO 180-1A
23℃	16	kJ/m²	ISO 180-1A
Notched impact strength of cantilever beam			ISO 180/1U
-30℃	80	kJ/m²	ISO 180/1U
23℃	80	kJ/m²	ISO 180/1U

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	213	℃	ISO 75-2/A
0.45 MPa, unannealed	220	℃	ISO 75-2/B
Vicat Softening Temp
B120	210	℃	ISO 306/B120
Melting temperature	222	℃	ISO 11357-3
Linear coefficient of thermal expansion
TD：23~55℃	7.5E-5	1/℃	ISO 11359-2
MD：23~55℃	1.2E-5	1/℃	ISO 11359-2

Electrical performance	Nominal value	Unit	Test method
Volume resistivity
23℃	5.8E+14	ohms·cm	IEC 60093
Dielectric strength
23 ℃，1 mm	33	kV/mm	IEC 60243-1
Relative permittivity			IEC 60250
23℃，100 Hz	5.30		IEC 60250
23℃，1 MHz	4.70		IEC 60250
Dissipation factor			IEC 60250
23℃，100 Hz	0.016		IEC 60250
23℃，1 MHz	0.018		IEC 60250
Compared to the leakage tracing index
Solution A	600	V	IEC 60112

Supplementary information	Nominal value	Unit	Test method
ISO Shortname	PA 6, GHR, 10-220, GF60		ISO 1874

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
23℃	20000	MPa	ISO 527-1-2
tensile strength
Fracture, 23 ℃	225	MPa	ISO 527-2/5
Tensile strain
Fracture, 23 ℃	2.4	%	ISO 527-2/5
Bending modulus
23℃	19300	MPa	ISO 178-A
bending strength
23℃	365	MPa	ISO 178-A
Bending strain	2.8	%	ISO 178/A
Ball hardness	255	MPa	ISO 2039-1

Process Conditions
injection	Nominal value	Unit	Test method
Drying Temperature – Dry Air Dryer	80	°C
Drying Time – Dry Air Dryer	2.0 to 6.0	hr
Processing (melt) temperature	270 to 290	°C
Mold temperature	80 to 120	°C
Residual Moisture Content	0.060 to 0.20	%

Notes
1. Typical properties: these are not to be construed as specifications.
2. 60x60x2mm, 4 hr
3. 60x60x2mm, 80°C MT, 600 bar
4. 0.079 in/min
5. 2 mm/min
6. 10°C/min
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.