Borcoat™ ME0420

About
Borcoat ME0420 is a maleic anhydride grafted polyethylene adhesive. The product is supplied in pellet form Applications Borcoat ME0420 is recommended as an adhesive for a three layer PE system used in: Steel Pipe Coating Specifications Borcoat ME0420 is intended to fulfill following National and International standards, when appropriate industrial manufacturing standard procedures are applied and a continuous quality system is implemented and when used in combination with Borcoat HE3450, HE3450-H or HE3453 and a compatible Fusion Bonded Epoxy(FBE) powder. NF A49-710 CAN/CSA-Z245.21 EN ISO 21809-1 DIN 30670 Special features Borcoat ME0420 is intended to be used as an adhesive for PE three layer systems at design temperatures between -40°C up to +90°C.&&

About

Borcoat ME0420 is a maleic anhydride grafted polyethylene adhesive. The product is supplied in pellet form Applications Borcoat ME0420 is recommended as an adhesive for a three layer PE system used in: Steel Pipe Coating Specifications Borcoat ME0420 is intended to fulfill following National and International standards, when appropriate industrial manufacturing standard procedures are applied and a continuous quality system is implemented and when used in combination with Borcoat HE3450, HE3450-H or HE3453 and a compatible Fusion Bonded Epoxy(FBE) powder. NF A49-710 CAN/CSA-Z245.21 EN ISO 21809-1 DIN 30670 Special features Borcoat ME0420 is intended to be used as an adhesive for PE three layer systems at design temperatures between -40°C up to +90°C.&&

Product Description
Supplier	Borealis AG
Generic	PE
Material Status	Commercial: Active
Features	Renewable resources,Good bond
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.934	g/cm³	ISO 1183
Melt Flow Rate
190℃，2.16kg	1.3	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	47		ISO 868
tensile strength
fracture	> 18.0	MPa	ISO 527-2/50
Tensile strain
fracture	> 700	%	ISO 527-2/50

film	Nominal value	Unit	Test method
peel strength			DIN 30670
23℃	> 2.00	J	DIN 30670
80℃	> 0.400	J	DIN 30670

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -80.0	℃	ASTM D746
Vicat Softening Temp
A50	100	℃	ISO 306/A50
Melting temperature
DSC	122	℃	ISO 3146

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel 1 zone temperature	200 to 230	°C
Barrel 2 zone temperature	200 to 230	°C
Barrel 3 zone temperature	200 to 230	°C
Barrel 4 zone temperature	200 to 230	°C
Barrel 5 zone temperature	200 to 230	°C
Melt temperature	210 to 230	°C
Nozzle temperature	230 to 240	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.