| About |
|---|
| This metallocene linear low density polyethylene is an ethylene-hexene copolymer tailored for blown film applications that require: Superb clarity Excellent gloss Exceptional toughness Outstanding heat seal Typical blown film applications include: Seal layer in coextrusions Heavy duty packaging Clarity packaging&& |
| Product Description | |
|---|---|
| Supplier | Chevron Phillips |
| Generic | mLLDPE |
| Material Status | Commercial: Active |
| Features | Good Clarity,Good flexibility,Good surface appearance,Good heat sealing,High anti-blocking,Low density,Copolymer,Hexene copolymers |
| Availabilitys | North America,Latin America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 1.0 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | |||
| Blown film | 0.90 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 25 | µm | |
| Secant modulus | |||
| 1% secant, MD: 25 µ m, blow molded film | 165 | MPa | |
| 1% secant, TD: 25 µ m, blow molded film | 188 | MPa | |
| tensile strength | |||
| MD, yield, 25 µ m, blow molded film | 12.8 | MPa | |
| TD, yield, 25 µ m, blow molded film | 9.65 | MPa | |
| MD, fracture, 25 µ m, blow molded film | 57.2 | MPa | |
| TD, fracture, 25 µ m, blow molded film | 45.9 | MPa | |
| Tensile strain | |||
| MD, fracture, 25 µ m, blow molded film | 450 | % | |
| TD, fracture, 25 µ m, blow molded film | 560 | % | |
| Drop hammer impact | |||
| 25 µ m, blow molded film | 600 | g | ASTM D1709 |
| Elmandorf tear strength | |||
| MD: 25 µ m, blow molded film | 230 | g | |
| TD: 25 µ m, blow molded film | 440 | g | |
| Initial sealing temperature | |||
| 25 µ m, blow molded film | 102 | ℃ | ASTM F88 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 60 °, 25.4 µ m, blow molded film | 103 | ASTM D2457 | |
| Haze | |||
| 25.4 µ m, blow molded film | 9.0 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Temperature at which 0.3 lb/in heat seal strength is achieved. 0.5 s dwell, 30 psi pressure, 11.8 in/min separation rate. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |