| About |
|---|
| Sarlink ME-2390B-01 BLK is a general purpose Thermoplastic Elastomer used in automotive applications. Sarlink ME-2390B-01 BLK is a high hardness, low density grade exhibiting good moldability characteristics. This grade is suitable for injection molding.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Excellent Processability,Good Hardness,Lubricating,Low density,Moderate liquidity |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Shore hardness | ISO 868 | ||
| Shore A, 1 second, injection molding | 90 | ISO 868 | |
| Shore A, 5 seconds, injection molding | 89 | ISO 868 | |
| Shore A, 15 seconds, injection molding | 88 | ISO 868 | |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ISO 37 | ||
| TD, 100% strain | 4.20 | MPa | ISO 37 |
| MD, 100% strain | 5.49 | MPa | ISO 37 |
| Tensile strain | ISO 37 | ||
| TD, fracture | 820 | % | ISO 37 |
| Flow rate, fracture | 620 | % | ISO 37 |
| tear strength | ISO 34-1 | ||
| TD | 50 | kN/m | ISO 34-1 |
| MD | 53 | kN/m | ISO 34-1 |
| Compression deformation | ISO 815 | ||
| 23℃，22 hr | 33 | % | ISO 815 |
| 70℃，22 hr | 51 | % | ISO 815 |
| 90℃，70 hr | 66 | % | ISO 815 |
| 125℃，70 hr | 96 | % | ISO 815 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | ISO 188 | ||
| TD：110℃，1008 hr | -7.1 | % | ISO 188 |
| MD：110℃，1008 hr | -16 | % | ISO 188 |
| TD: 100% strain at 110 ℃, 1008 hr | 14 | % | ISO 188 |
| MD: 100% strain at 110 ℃, 1008 hr | 14 | % | ISO 188 |
| TD：125℃，168 hr | -9.2 | % | ISO 188 |
| MD：125℃，168 hr | -18 | % | ISO 188 |
| MD: 100% strain 125 ℃, 168 hr | 14 | % | ISO 188 |
| TD: 100% strain 168 ℃, 125 hr | 2.8 | % | ISO 188 |
| The rate of change of Shore hardness in air | ISO 188 | ||
| Shore A, 110 ℃, 1008 hr | 2.2 | ISO 188 | |
| Shore A, 110 ℃, 1008 hr | 1.8 | ISO 188 | |
| Shore A, 110 ℃, 1008 hr | 1.3 | ISO 188 | |
| Shaw A, 125 ℃, 168 hr | 1.0 | ISO 188 | |
| Shaw A, 125 ℃, 168 hr | 0.70 | ISO 188 | |
| Shaw A, 125 ℃, 168 hr | -0.10 | ISO 188 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 0.900 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 9.0 | g/10min | ASTM D1238 |
| Apparent viscosity of melt | |||
| 200℃，206 sec^-1 | 222 | Pa·s | ASTM D3835 |
| Special value | Nominal value | Unit | Test method |
|---|---|---|---|
| TD, fracture | 16.5 | MPa | ISO 37 |
| MD, fracture | 10.5 | MPa | ISO 37 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 199 to 210 | °C | |
| Barrel middle temperature | 204 to 216 | °C | |
| Barrel front temperature | 210 to 221 | °C | |
| Nozzle temperature | 216 to 227 | °C | |
| Processing (melt) temperature | 216 to 227 | °C | |
| Mold temperature | 35 to 66 | °C | |
| Injection pressure | 1.38 to 6.89 | MPa | |
| Injection speed | 快速 | ||
| Back pressure | 0.172 to 0.862 | MPa | |
| Screw speed | 50 to 120 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type 1, 20 in/min |
| 3. Method Ba, Angle (Unnicked), 20 in/min |
| 4. Type A |
| 5. Type 1 |
| 6. Instant |
| 7. 5 sec |
| 8. 15 sec |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |