| About |
|---|
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS |
| Material Status | Commercial: Active |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.43 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 300℃，10.0kg | 31 | g/10min | |
| 300℃，5.0kg | 9.5 | g/10min | |
| Melt Volume Rate | |||
| 300℃，10 kg | 23.5 | cm³/10min | |
| 300℃，5 kg | 7.00 | cm³/10min | |
| Shrinkage rate | |||
| MD：24 hrs | 0.75 to 0.85 | % | |
| TD：24 hrs | 0.75 to 0.85 | % | |
| Water absorption rate | |||
| 23℃，24hr | 0.030 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 2170 | MPa | ASTM D638 |
| — | 2080 | MPa | ISO 527-1-2 |
| Tensile strength | |||
| yield | 43.0 | MPa | ASTM D638 |
| fracture | 36.0 | MPa | ASTM D638 |
| fracture | 42.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 7.8 | % | ASTM D638 |
| fracture | 8.9 | % | ASTM D638 |
| fracture | 9.3 | % | ISO 527-2/50 |
| Bending modulus | |||
| 50 mm span | 2000 | MPa | ASTM D790 |
| — | 2230 | MPa | ISO 178 |
| Bending stress | |||
| — | 70.0 | MPa | ISO 178 |
| — | 72.0 | MPa | ISO 178 |
| Yield, 50.0 mm span | 65.0 | MPa | ASTM D790 |
| Fracture, 50.0 mm span | 63.0 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| -20℃ | 170 | J/m | ASTM D256 |
| 23℃ | 210 | J/m | ASTM D256 |
| -20℃ | 16 | kJ/m² | ISO 180-1A |
| 23℃ | 21 | kJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 3.2 mm | 173 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 4.0 mm, 64 mm span | 174 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, unannealed, 3.2 mm | 148 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 4.0 mm, 64 mm span | 149 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | |||
| Flow: -40~150 ℃ | 6.1E-5 | 1/℃ | |
| TD：-40~150℃ | 8.3E-5 | 1/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | |||
| 1.10 GHz | 3.91 | ||
| 1.9 GHz | 3.93 | ||
| 5.00 GHz | 3.95 | ||
| 10.0 GHz | 3.93 | ||
| Dissipation factor | |||
| 1.1 GHz | 9.0E-4 | ||
| 1.9 GHz | 1.2E-3 | ||
| 5 GHz | 1.8E-3 | ||
| 10 GHz | 2.1E-3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.00-3.00 mm | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| drying temperature | 105 | °C | |
| Drying time | 3.0 to 5.0 | hr | |
| Temperature at the rear of the barrel | 275 to 285 | °C | |
| Temperature in the middle of the barrel | 280 to 295 | °C | |
| Front temperature of material barrel | 285 to 305 | °C | |
| Nozzle temperature | 280 to 295 | °C | |
| Processing (melt) temperature | 285 to 295 | °C | |
| Mold temperature | 90 | °C | |
| Back pressure | 9.00 | MPa | |
| Screw speed | 100 | rpm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |