| About |
|---|
| Bormed RF830MO is a resin intended for evaluation for use in Healthcare applications. Bormed RF830MO is a transparent polypropylene random copolymer, modified with a nucleating agent, suitable for articles which need post sterilisation with radiation. Bormed RF830MO is characterized by easy processability, high transparency, high gloss and a good stiffness-impact balance. Products moulded from this grade and radiated with the dose of 25 kGy have a shelf-life of 5 years, if properly stored. Material can also be sterilised with ethylene oxide and steam. Applications Bormed RF830MO has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed RF830MO . Disposable non pre-filled syringes Needle hubs Catheter connections Laboratory disposable Diagnostic products Blood collection tubes This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure.&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP copolymer |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Excellent Processability,Good Clarity,Good surface appearance,High impact resistance,High liquidity,Good Printability,Gamma radiation,Random copolymer,Radiation disinfection,Solvent resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.905 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 20 | g/10min | ISO 1133 |
| Shrinkage rate | 1.0 to 2.0 | % | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 6.0 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 80.0 | ℃ | ISO 75-2/B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1150 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 28.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 12 | % | ISO 527-2/50 |
| Rockwell hardness | |||
| R-level | 90 | ISO 2039-2 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 220 to 250 | °C | |
| Mold temperature | 30 to 40 | °C | |
| Injection speed | Moderate-Fast | ||
| Hold pressure | 20.0 to 50.0 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Injection molded specimen |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |