| About |
|---|
| The chemical compatibilization of polyetheretherketone (PEEK) and polytetrafluoroethylene (PTFE) will result in a semi-crystalline thermoplastic polymer compound with a homogeneous and stable processing morphology. The compound exhibits improved impact strength and excellent tribological properties. The thermal and chemical resistance corresponds to the properties of the PEEK matrix material. The granules can be processed under the processing conditions of the matrix material by extrusion or injection molding.&& |
| Product Description | |
|---|---|
| Material Status | Commercial: Active |
| Features | High impact resistance,Excellent Processability,Hypocrystalline |
| Availabilitys | Europe |
| Process Methods | Extrusion,Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.34 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 380℃，5.0kg | 37 | g/10min | ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 3200 | MPa | ISO 527-2/1A/1 |
| tensile strength | 78.0 | MPa | ISO 527-2/1A/50 |
| Tensile strain | ISO 527-2/1A/50 | ||
| yield | 5.0 | % | ISO 527-2/1A/50 |
| fracture | 9.0 | % | ISO 527-2/1A/50 |
| Bending modulus | 3150 | MPa | ISO 178 |
| bending strength | 123 | MPa | ISO 178 |
| friction coefficient | 0.18 | ISO 7148 | |
| Bending strain | 6.4 | % | ISO 178 |
| Wear Coefficient | 2.10E-6 | mm³/(N·m | ISO 7148 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 19 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 无断裂 | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | 152 | ℃ | ISO 11357-2 |
| Melting temperature | ISO 11357-3 | ||
| — | 325 | ℃ | ISO 11357-3 |
| — | 340 | ℃ | ISO 11357-3 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | IEC 60250 | ||
| 1 kHz | 3.10 | IEC 60250 | |
| 1 MHz | 3.10 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 1 kHz | 1.0E-3 | IEC 60250 | |
| 1 MHz | 0.010 | IEC 60250 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Block / ring test: FN = 100 N, v = 0,11 m/s, s = 10.000 m, Counterbody: Steel 100 Cr6, Rz = 3.2 microns, Conditions: technically dry |
| 3. PTFE |
| 4. PEEK |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |