| About |
|---|
| Rilsan® AMN Y TLD是一种聚酰胺12（尼龙12）产品,含有的填充物为填料。 它可以通过注射成型进行加工,在北美洲、非洲和中东、拉丁美洲、欧洲或亚太地区有供货。 特性包括: 良好的抗紫外线能力 热稳定剂 脱模剂&& |
| Product Description | |
|---|---|
| Supplier | Arkema |
| Generic | PA12 |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Heat Stabilized,HB,V-2 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.02 | g/cm³ | ISO 1183-2 |
| Melt Volume Rate | |||
| 235℃，2.16 kg | 50.0 | cm³/10min | ISO 1133 |
| Water absorption rate | |||
| saturated | 1.6 | % | ISO 62-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1500 | MPa | ISO 527-2 2 |
| tensile strength | |||
| yield | 50.0 | MPa | ISO 527-2 2 |
| Tensile strain | |||
| yield | 9.0 | % | ISO 527-2 2 |
| Nominal strain at break | > 50 | % | ISO 527-2 2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 65.0 | ℃ | ISO 75-2 2 |
| 0.45 MPa | 143 | ℃ | ISO 75-2 2 |
| Vicat Softening Temp | |||
| B50 | 145 | ℃ | ISO 306 2 |
| Melting temperature | 178 | ℃ | ISO 11357-3 2 |
| Linear coefficient of thermal expansion | |||
| MD | 9.0E-5 | 1/℃ | ISO 11359-2 2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | — | ohms | IEC 60093 2 |
| Volume resistivity | — | ohms·m | IEC 60093 2 |
| Dielectric strength | — | kV/mm | IEC 60243-1 2 |
| Relative permittivity | |||
| 100 Hz | 3.00 | IEC 60250 2 | |
| 1 MHz | 3.00 | IEC 60250 2 | |
| Dissipation factor | |||
| 100 Hz | 0.077 | IEC 60250 2 | |
| 1 MHz | 0.028 | IEC 60250 2 | |
| Compared to the leakage tracing index | |||
| CTI | — | IEC 60112 2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60 mm | HB | ISO 1210 2 | |
| Flame retardant level | |||
| 3.20 mm | V-2 | ISO 1210 2 | |
| Oxygen index | 22 | % | ISO 4589-2 2 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |