| About |
|---|
| Extrusion molding grade, Light diffusion grade, Weather resistance, Flame resistance&& |
| Product Description | |
|---|---|
| Supplier | TEIJIN |
| Generic | Polycarbonate |
| Material Status | Commercial: Negative |
| Features | Weather resistance is good,Low Light Diffusion,Flame Characteristics,V-0,5VA |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.20 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 300℃，1.2 kg | 2.50 | cm³/10min | ISO 1133 |
| Shrinkage rate | Internal Method | ||
| TD：4.0 mm | 0.50 to 0.70 | % | Internal Method |
| MD：4.0 mm | 0.50 to 0.70 | % | Internal Method |
| Water absorption rate | |||
| 23℃，24hr | 0.20 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2400 | MPa | ISO 527-1-2 |
| tensile strength | ISO 527-2/50 | ||
| yield | 65.0 | MPa | ISO 527-2/50 |
| fracture | 53.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 6.0 | % | ISO 527-2/50 |
| Nominal tensile fracture strain | 25 | % | ISO 527-2/50 |
| Bending modulus | 2350 | MPa | ISO 178 |
| bending strength | 97.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 9.0 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | |||
| 23℃ | 无断裂 | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 123 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | ISO 11359-2 | ||
| MD | 7.0E-5 | 1/℃ | ISO 11359-2 |
| TD | 7.0E-5 | 1/℃ | ISO 11359-2 |
| Relative temperature index | |||
| Electrical performance, 1.50 mm | 130 | ℃ | UL 746 |
| Impact mechanical performance, 1.50 mm | 125 | ℃ | UL 746 |
| 1.50 mm | 130 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | > 1.0E+15 | ohms·cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.50 mm | V-0 | UL 94 | |
| 3.20 mm | 5VA | UL 94 | |
| Glowing wire flammability index | IEC 60695-2-12 | ||
| 1.5 mm | 960 | ℃ | IEC 60695-2-12 |
| 3.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | IEC 60695-2-13 | ||
| 1.5 mm | 850 | ℃ | IEC 60695-2-13 |
| 3 mm | 850 | ℃ | IEC 60695-2-13 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | |||
| 3000 µm | 77.0 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |