| About |
|---|
| TECANAT is a natural unfilled polycarbonate that has transparency, excellent impact strength and tensile properties, TECANAT GF20 is a 20% glass-reinforced polycarbonate with higher temperature and tensile properties than the unfilled TECANAT. Polycarbonate is an amorphous thermoplastic. Good electrical properties combined with superior impact strength and moderate chemical resistance make this product widely accepted for numerous applications, This product is offered in many popular rod and plate sizes. Typical applications include business equipment where gears, rollers, internal mechanical parts, connectors and relays are required. The automotive industry uses polycarbonate materials for pumps, valves, light bezels and instrument panels. It also is applicable to many other industries. Superior impact strength Outstanding mechanical strength and stiffness Excellent dimensional stability Good electrical properties Transparency Good Machinability&& |
| Product Description | |
|---|---|
| Supplier | Ensinger |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Clarity,High impact resistance,Good Dimensional Stability,Good Electrical Properties,Machinable,Solvent resistance,Amorphous,V-0 |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.33 | g/cm³ | ASTM D792 |
| Water absorption rate | ASTM D570 | ||
| 23℃，24hr | 0.16 | % | ASTM D570 |
| Saturation, 23 ℃ | 0.29 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Notched impact strength of cantilever beam | |||
| 23℃ | 110 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, injection molded | 148 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, injection molded | 146 | ℃ | ASTM D648 |
| Vicat Softening Temp | 165 | ℃ | ASTM D1525 |
| Linear coefficient of thermal expansion | |||
| MD | 2.7E-5 | 1/℃ | ASTM D696 |
| Maximum operating temperature | |||
| Intermittent | 135 | ℃ | |
| long-term | 130 | ℃ | UL 746B |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | 19 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 1 MHz | 3.13 | ASTM D150 | |
| 23 ℃，60 Hz | 3.17 | ASTM D150 | |
| Dissipation factor | |||
| 23℃，60 Hz | 9.0E-4 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 3.00 mm | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-grade, 23 ℃, injection molding | 87 | ASTM D785 | |
| Tensile modulus | 4830 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 23 ℃ | 82.7 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 4.0 | % | ASTM D638 |
| Bending modulus | |||
| 23℃ | 4270 | MPa | ASTM D790 |
| bending strength | |||
| 23℃ | 124 | MPa | ASTM D790 |
| compressive strength | ASTM D695 | ||
| 1% strain | 20.7 | MPa | ASTM D695 |
| 10% strain | 75.8 | MPa | ASTM D695 |
| friction coefficient | |||
| With oneself – dynamic | 0.22 | ||
| Wear factor | |||
| 0.28 MPa，0.25 m/sec | 240 | 10^-8 mm³/N·m | ASTM D3702 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 40 psi, 50 fpm |
| 3. 50% RH |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |