| About |
|---|
| Extrusion- and injection molding grade; very good hydrolysis and microbial resistance; good low-temperature flexibility; complies with VDE 0282-10; This product is manufactured under Good Manufacturing Practice (GMP defined in Regulation (EC) No. 2023/2006) and is therefore limited suitability for use with food contact. Please refer our separate certificate at http://www.tpu.covestro.com/en/Library/Certificates/Food-Contact.aspx.; Application; Cable sheathings; Hoses, non-reinforced&& |
| Product Description | |
|---|---|
| Supplier | Covestro |
| Generic | TPU |
| Material Status | Commercial: Active |
| Features | Hydrolysis stability,Antimicrobial properties,Food contact compliance,Low temperature toughness |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.12 | g/cm³ | ISO 1183 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tear strength | |||
| 23℃ | 65 | kN/m | ISO 34-1 |
| Compression deformation | |||
| 23℃，72 hr | 25 | % | |
| 70℃，24 hr | 41 | % | |
| 70℃，24 hr | 30 | % | |
| Resilience | 40 | % | ISO 4662 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 1 second, 23 ℃ | 86 | ||
| Shore D, 1 second, 23 ℃ | 35 | ||
| tensile strength | |||
| Fracture, 23 ℃ | 39.1 | MPa | |
| 10% strain, 23 ℃ | 2.00 | MPa | |
| 50% strain, 23 ℃ | 5.30 | MPa | |
| 100% strain, 23 ℃ | 6.80 | MPa | |
| 300% 应变, 23°C | 12.2 | MPa | |
| Tensile strain | |||
| Fracture, 23 ℃ | 600 | % | DIN 53504 |
| Tensile storage modulus | |||
| -20℃ | 118 | MPa | |
| 20℃ | 32.0 | MPa | |
| 60℃ | 23.0 | MPa | |
| 25.0 | mm³ | ISO 4649 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | < 80 | °C | |
| Processing (melt) temperature | 205 to 225 | °C | |
| Mold temperature | 20 to 40 | °C | |
| Drying temperature | < 80 | °C | |
| Melt temperature | 195 to 215 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 7.9 in/min |
| 3. Method A |
| 4. 20 in/min |
| 5. Method C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |