Derakane® 510N

About
DERAKANE 510N resin is a brominated novolac epoxy vinyl ester resin that offers a moderate degree of fire retardance. It is the preferred resin the DERAKANE resin portfolio for strong oxidizers, such as chlorine and chlorine dioxide. It is also useful in hot, Wet fluegas environments vvhere thermal upsets can occur and vvhere fire retardance is desired. It exhibits a corrosion resistance similarto DERAKANE 470 resins in most environments. APPLICATIONS AND USE DERAKANE 51ON resin is used extensively in FRP ductvvork, stacks, and stack liner applications, equipment specified to handle mixtures ofair and hot gases or potentially flammable and corrosive liquids, and flooring compounds where heat and/or fire retardance is required. DERAKANE 51ON resin is recommended for most FRP fabrication processes including filament winding, hand lay—up, spray—up, pultrusion and resin transfer molding.&&

About

DERAKANE 510N resin is a brominated novolac epoxy vinyl ester resin that offers a moderate degree of fire retardance. It is the preferred resin the DERAKANE resin portfolio for strong oxidizers, such as chlorine and chlorine dioxide. It is also useful in hot, Wet fluegas environments vvhere thermal upsets can occur and vvhere fire retardance is desired. It exhibits a corrosion resistance similarto DERAKANE 470 resins in most environments. APPLICATIONS AND USE DERAKANE 51ON resin is used extensively in FRP ductvvork, stacks, and stack liner applications, equipment specified to handle mixtures ofair and hot gases or potentially flammable and corrosive liquids, and flooring compounds where heat and/or fire retardance is required. DERAKANE 51ON resin is recommended for most FRP fabrication processes including filament winding, hand lay—up, spray—up, pultrusion and resin transfer molding.&&

Product Description
Generic	乙烯基酯
Material Status	Commercial: Active
Features	Flame Characteristics,Bromination
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.25	g/cm³	ISO 1183
Solution viscosity	275	mPa·s
styrene content	37	%

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	121	℃	ASTM D648，ISO 75-2/A

Supplementary information	Nominal value	Unit	Test method
Volume contraction	8.4	%

MECHANICAL	Nominal value	Unit	Test method
Babbitt hardness	40		ASTM D2583
Tensile modulus
—	3450	MPa	ASTM D638
—	3400	MPa	ISO 527-2
tensile strength
—	72.4	MPa	ASTM D638
—	76.0	MPa	ISO 527-2
Tensile strain
yield	3.0 to 4.0	%	ASTM D638 , ISO 527-2
Bending modulus
—	3650	MPa	ASTM D790
—	3600	MPa	ISO 178
bending strength
—	131	MPa	ASTM D790
—	138	MPa	ISO 178

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.