| About |
|---|
| High performance thermoplastic material, 30% glass fibre reinforced PolyEtherEtherKetone (PEEK), semi crystalline, granules for injection moulding, easy flow, FDA food contact compliant, colour black. Complex geometries with thin cross sections or long flow lengths where higher strength in a static system is required. Low coefficient of thermal expansion. Chemically resistant to aggressive environments, suitable for sterilization for medical and food contact applications.&& |
| Product Description | |
|---|---|
| Supplier | Victrex |
| Material Status | Commercial: Active |
| Features | Solvent resistance,Good disinfection,Good Rigidity,Food contact compliance,Hypocrystalline,Good liquidity |
| Availabilitys | Europe,Latin America,Africa & Middle East ,North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile Strength | |||
| Broken BRK, 23 ℃ | 190 | MPa | ISO 527-2 |
| Broken BRK, 125 ℃ | 115 | MPa | ISO 527-2 |
| Broken BRK, 175 ℃ | 70 | MPa | ISO 527-2 |
| Broken BRK, 225 ℃ | 60 | MPa | ISO 527-2 |
| Broken BRK, 275 ℃ | 40 | MPa | ISO 527-2 |
| Elongation at Break | 2.4 | % | ISO 527-2 |
| Tensile Modulus | 12 | GPa | ISO 527 |
| Flexural Strength | |||
| 23℃ | 270 | MPa | ISO 178 |
| 125℃ | 195 | MPa | ISO 178 |
| 175℃ | 115 | MPa | ISO 178 |
| 175℃ | 70 | MPa | ISO 178 |
| Flexural Modulus | 11.5 | MPa | ISO 178 |
| Compressive Strength | |||
| 23℃ | 250 | MPa | ISO 604 |
| 120℃ | 160 | MPa | ISO 604 |
| 200℃ | 55 | MPa | ISO 604 |
| Shore hardness | 87 | ISO 868 | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Izod Notched Impact strength | 8.5 | KJ/m² | ISO 180/1A |
| Izod Unnotched Impact strength of cantilever beam | 50 | KJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting point | 343 | ℃ | ISO 11357 |
| Glass Transition Temperature | |||
| Start Onset | 143 | ℃ | ISO 11357-2 |
| Midpoint | 147 | ℃ | ISO 11357-2 |
| Coeff. of linear thermal expansion | |||
| Along flow below | 20 | ppm K-1 | ISO 11359-2 |
| Average below | 45 | ppm K-1 | ISO 11359-2 |
| Along flow below | 20 | ppm K-1 | ISO 11359-2 |
| Average below | 110 | ppm K-1 | ISO 11359-2 |
| Hot deformation temperature HDT | |||
| 1.8 MPa | 335 | ℃ | ISO 75-1/-2 |
| Thermal conductivity | |||
| Along flow | 0.35 | W/m/K | ISO 22007-4 |
| Average | 0.30 | W/m/K | ISO 22007-4 |
| Relative Temperature Index (RTI) | |||
| Electrical | 240 | ℃ | UL-746B |
| Non mechanical w/o impact | 240 | ℃ | UL-746B |
| 240 | ℃ | UL-746B |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| 275 | Pa.s | ISO 11443 | |
| Density | 1.52 | g/cm³ | ISO 1183 |
| Water Absorption | |||
| Saturation, 23 ℃ | 0.3 | % | ISO 62 |
| Saturation, 100 ℃ | 0.45 | % | ISO 62 |
| Molding shrinkage | |||
| Along flow | 0.3 | % | ISO 294-4 |
| Across flow | 0.9 | % | ISO 294-4 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric Strength | 21.5 | kV/mm | IEC 60243-1 |
| Compared Tracking Index | 150 | V | IEC 60112 |
| 0.004 | IEC 60250 | ||
| Dielectric Constant | 3.4 | IEC 60250 | |
| Volume Resistance | 5E15 | ohm·cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Glow Wire Flammability Index (GWFI) | 960 | ℃ | IEC 60695-2-12 |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 150-120 | ℃ | |
| Drying Time | 3-5 | hr | |
| Rear Temperature Zone 1 | 360-365 | ℃ | |
| Middle Temperature Zone 2 | 365-370 | ℃ | |
| Front Temperature Zone 3 | 370-375 | ℃ | |
| Nozzle temperature | 375-380 | ℃ | |
| Hopper Temperature | 100 | ℃ | |
| Mold Temperature | 170-200 | ℃ | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Crystalline |
| 3. Mold Temperature: 356°F, Melt Temperature: 716°F |
| 4. 1 mm |
| 5. 380°C nozzle, 180°C tool |
| 6. Onset |
| 7. Midpoint |
| 8. Average |
| 9. Along flow |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |