| About |
|---|
| Product Description | |
|---|---|
| Supplier | LG Chemical |
| Generic | ABS |
| Material Status | Commercial: Negative |
| Features | Flame Characteristics,Heat Resistance, Good,V-1 |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.19 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 220℃，10.0kg | 37 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.40-0.70 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 103 | ASTM D785 | |
| Tensile modulus | |||
| 3.20 mm | 2156 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 3.20 mm | 42 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| Yield, 3.20 mm | 5.0 | % | ASTM D638 |
| Fracture, 3.20 mm | 20 | % | ASTM D638 |
| Bending modulus | |||
| 6.40 mm | 2352 | MPa | ASTM D790 |
| bending strength | |||
| 6.40 mm | 68.6 | MPa | ASTM D790 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, 6.4 mm | 89.0 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.4 mm | 80.0 | ℃ | ASTM D648 |
| Vicat Softening Temp | 88 | ℃ | ASTM D1525 6 |
| Relative temperature index | 60.0 | ℃ | UL 746 |
| Electrical performance | 60.0 | ℃ | UL 746 |
| Impact mechanical performance | 60.0 | ℃ | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.80 mm | V-0 | UL 94 | |
| 2.00 mm | 5VB | UL 94 | |
| 2.50 mm | 5VA | UL 94 | |
| 3.00 mm | V-0 | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| drying temperature | 70-80 | °C | |
| Drying time | 2-4 | hr | |
| Temperature at the rear of the barrel | 170 – 190 | °C | |
| Temperature in the middle of the barrel | 180 – 200 | °C | |
| Front temperature of material barrel | 190 – 210 | °C | |
| Nozzle temperature | 200 – 230 | °C | |
| Processing (melt) temperature | 200 – 230 | °C | |
| Mold temperature | 40 – 60 | °C | |
| Back pressure | 0.490 – 0.981 | MPa | |
| Screw speed | 30 – 60 | rpm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |