| About |
|---|
| Lupolen 5261 Z is a high density polyethylene with high impact resistance, high rigidity, high chemical resistance and good ESCR. It is delivered in powder form and contains antioxidants. Typical customer applications include open top drums and jerry cans for the packaging of dangerous goods. Lupolen 5261 Z is not intended for use in medical and pharmaceutical applications.&& |
| Product Description | |
|---|---|
| Supplier | LyondellBasell |
| Generic | HDPE |
| Material Status | Commercial: Active |
| Features | Good Rigidity,High impact resistance,Inoxidizability,High density,Solvent resistance,High ESCR |
| Availabilitys | Africa & Middle East ,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.954 | g/cm³ | ISO 1183 |
| Apparent density | > 0.46 | g/cm³ | ISO 60 |
| Melt Flow Rate | |||
| 190℃，21.6kg | 2.0 | g/10min | ISO 1133 |
| Full incision creep test | |||
| 3.5 MPa，80℃ | 12.0 | hr | ISO 16770 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile impact strength | |||
| -30℃ | 250 | kJ/m² | ISO 8256/1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 75.0 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 44.0 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| A50 | 132 | ℃ | ISO 306/A50 |
| B50 | 80.0 | ℃ | ISO 306 |
| Melting temperature | |||
| DSC | 134 | ℃ | ISO 3146 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | > 150 | kV/mm | IEC 60243-1 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Staudinger index | |||
| Jg | 475 | cm³/g | ISO 1628 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | |||
| H 132/30 | 52.0 | MPa | ISO 2039-1 |
| Tensile modulus | |||
| 23℃ | 1200 | MPa | ISO 527-2 |
| tensile strength | |||
| Yield, 23 ℃ | 27.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| yield | 9.0 | % | ISO 527-2 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Melt temperature | 190 to 220 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2% Arkopal N100 |
| 3. K20/P50 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |