| About |
|---|
| Adsyl 3 C 30 F HP is an advanced polyolefin, specially designed for use as a sealing or metallized layer in co-extruded film applications. This grade features a low seal initiation temperature, a high melting point and good optics. It does not contain slip or anti-block additives. For regulatory information please refer to Adsyl 3 C 30 F HP Product Stewardship Bulletin (PSB).&& |
| Product Description | |
|---|---|
| Supplier | LyondellBasell |
| Generic | 聚烯烃，共挤薄膜用聚烯烃 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Optical performance,Food contact compliance,High Heat Resistance,Low temperature heat sealing |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.900 | g/cm³ | ISO 1183/A |
| Melt Flow Rate | |||
| 230℃，2.16kg | 5.5 | g/10min | ISO 1133 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 50 | µm | |
| Secant modulus | |||
| TD, 50 µ m, cast thin film | 400 | MPa | ASTM D882 |
| MD, 50 µ m, cast thin film | 400 | MPa | ASTM D882 |
| tensile strength | |||
| TD, fracture, 50 µ m, blow molded film | 38.0 | MPa | ASTM D882 |
| TD, yield, 50 µ m, blow molded film | 18.0 | MPa | ASTM D882 |
| MD, fracture, 50 µ m, blow molded film | 44.0 | MPa | ASTM D882 |
| MD, yield, 50 µ m, blow molded film | 18.0 | MPa | ASTM D882 |
| Tensile strain | |||
| TD, fracture, 50 µ m, cast thin film | 850 | % | ASTM D882 |
| TD, yield, 50 µ m, cast thin film | 10 | % | ASTM D882 |
| MD, fracture, 50 µ m | 850 | % | ASTM D882 |
| MD, yield, 50 µ m, cast thin film | 12 | % | ASTM D882 |
| Initial sealing temperature | 112 | ℃ |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 71.0 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | |||
| A50 | 122 | ℃ | ISO 306/A50 |
| Melting temperature | 137 | ℃ | DSC |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45°，50 µm | 91 | ASTM D2457 | |
| Haze | |||
| 50 µm | 0.40 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |