SOLPLAST TH 8000A

About
Is a commercial name for thermoplastic elastomers (TPE – S) based on SBS, SEBS (styrene – butadiene – styrene; styrene – ethilene butadiene – styrene) block copolymers, gathered with mixing SBS, SEBS, … elastomers with polyolefines such as PP, PE, EVA, … Resistance to acid, bases and all aqueous solutions is excellent. Resistance to alcohol and glycols is medium good. Resistance to aromatic hydrocarbons, fat and of oil is bad. Resistace round series upwards loosely increases. All “SOLPLASTS” have a good electric-volume resistance: thats more then 1e12 ohm-cm. For coloring masters are used on a polyolefine base (PE, PP, EVA). SERIES 8000 Technical compaund on SBS + SEBS block copolymers base; Different phisical characteristics and optics considering purpose of use. Work temperature between – 50 in + 60°C, very shortly up to +80°C For aplication with higher coloral stability of the product under light exposure. Approved stability to higher temperatures at shortime loads. 8000 A Injection moulded products&&

About

Is a commercial name for thermoplastic elastomers (TPE – S) based on SBS, SEBS (styrene – butadiene – styrene; styrene – ethilene butadiene – styrene) block copolymers, gathered with mixing SBS, SEBS, … elastomers with polyolefines such as PP, PE, EVA, … Resistance to acid, bases and all aqueous solutions is excellent. Resistance to alcohol and glycols is medium good. Resistance to aromatic hydrocarbons, fat and of oil is bad. Resistace round series upwards loosely increases. All “SOLPLASTS” have a good electric-volume resistance: thats more then 1e12 ohm-cm. For coloring masters are used on a polyolefine base (PE, PP, EVA). SERIES 8000 Technical compaund on SBS + SEBS block copolymers base; Different phisical characteristics and optics considering purpose of use. Work temperature between – 50 in + 60°C, very shortly up to +80°C For aplication with higher coloral stability of the product under light exposure. Approved stability to higher temperatures at shortime loads. 8000 A Injection moulded products&&

Product Description
Generic	SEBS+SBS
Material Status	Commercial: Active
Features	Alkali resistant,Good color stability,Acidproof
Availabilitys	Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.04 to 1.16	g/cm³	ISO 1183
Melt Flow Rate	10 to 20	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s A	35 to 85		ISO 868

elastic body	Nominal value	Unit	Test method
Compression deformation
72℃，23 hr	55 to 65	%	ISO 815

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.