| About |
|---|
| Anjacom® 250-H/GF15 is a Polyamide 6 (Nylon 6) material filled with 15% glass fiber. It is available in Europe for injection molding. Important attributes of Anjacom® 250-H/GF15 are: Flame Rated Heat Stabilizer&& |
| Product Description | |
|---|---|
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Heat Stabilized |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.23 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD | 0.40 | % | ISO 294-4 |
| TD | 0.90 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | 8.50 | % | ISO 62 |
| 23℃，50% RH | 2.60 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 23℃ | 125 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 3 | % | ISO 527-2 |
| Tensile modulus | |||
| 23℃ | 6000 | MPa | ISO 527-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 190 | ℃ | ISO 75-2/Af |
| Vicat Softening Temp | |||
| B50 | 200 | ℃ | ISO 306/A50 |
| Melting temperature | 220 | ℃ | ISO 11357-3 |
| Ball pressure temperature | 210 | ℃ | IEC 60695-10-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Insulation strength | 25 | KV/mm | IEC 60243-1 |
| Compared to the leakage tracing index | 550 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60 mm | HB | UL 94 | |
| Relative temperature of heating wire | |||
| 3.00mm | 650 | ℃ | IEC 60695-2-13 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 45 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 6 | kJ/m² | ISO 179/1eA |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 4-10 | Hr | |
| Water content | 0.10 | % | |
| Injection temperature | |||
| Mold temperature | 80-120 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |