| About |
|---|
| Warning: The status of this material is ‘Commercial: Limited Issue’ The data for this material has not been recently verified. Please contact RTP Company for current information prior to specifying this grade.&& |
| Product Description | |
|---|---|
| Generic | PA610 |
| Material Status | Commercial: Negative |
| Features | Lubricating,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.34 | g/cm³ | ASTM D792 |
| Shrinkage rate | ASTM D955 | ||
| MD: 3.2 mm, injection molded | 0.10 | % | ASTM D955 |
| MD: 6.35mm, injection molded | 0.20 | % | ASTM D955 |
| Water absorption rate | |||
| 23℃，24hr | 0.20 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| injection molding | 17200 | MPa | ASTM D638 |
| tensile strength | 200 | MPa | ASTM D638 |
| Tensile strain | |||
| Yield, injection molding | 3.5 | % | ASTM D638 |
| Bending modulus | |||
| injection molding | 16500 | MPa | ASTM D790 |
| bending strength | |||
| injection molding | 296 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm, injection molded | 110 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 3.2 mm | 800 | J/m | ASTM D4812 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, injection molded | 221 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, injection molded | 216 | ℃ | ASTM D648 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+3 | ohms·cm | ASTM D257 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 274 to 293 | °C | |
| Barrel middle temperature | 274 to 293 | °C | |
| Barrel front temperature | 274 to 293 | °C | |
| Mold temperature | 22 to 107 | °C | |
| Injection pressure | 69.0 to 124 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |