| About |
|---|
| Description High Impact, Dimensional Stability, Good Weatherability Application Automotive(Door Garnish)&& |
| Product Description | |
|---|---|
| Supplier | LG Chemical |
| Generic | PC+PBT |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,High impact resistance,Good Dimensional Stability |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 250℃，5.0kg | 17 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.70 to 1.0 | % | ASTM D955 |
| Water absorption rate | |||
| 23℃，24hr | 0.080 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, 3.20 mm | 56.9 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 3.20 mm | > 100 | % | ASTM D638 |
| Bending modulus | |||
| 6.40 mm | 2110 | MPa | ASTM D790 |
| bending strength | |||
| Yield, 6.40 mm | 79.4 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -30℃，6.4mm | 170 | J/m | ASTM D256 |
| 23℃，6.4mm | 690 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 6.4 mm | 105 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 6.4 mm | 115 | ℃ | ASTM D648 |
| Melting peak temperature | 223 | ℃ | ASTM D3418 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 4.0 to 5.0 | hr | |
| Recommended maximum moisture content | < 0.020 | % | |
| Barrel rear temperature | 250 to 260 | °C | |
| Barrel middle temperature | 250 to 260 | °C | |
| Barrel front temperature | 255 to 265 | °C | |
| Nozzle temperature | 260 to 270 | °C | |
| Processing (melt) temperature | 260 to 270 | °C | |
| Mold temperature | 60 to 80 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. 0.098 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |