| About |
|---|
| Amodel® ET-1000 HS is an impact modified, heat stabilized polyphthalamide (PPA) that exhibits exceptional impact strength and toughness. Like all Amodel® PPA resins, ET-1000 HS offers high fatigue strength, good chemical resistance and high mechanical property retention over a broad temperature and humidity range. Natural: ET-1000 HS NT&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | PPA |
| Material Status | Commercial: Active |
| Features | Low warping,High impact resistance,Ductility,Solvent resistance,Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.13 | g/cm³ | ISO 1183/A |
| Shrinkage rate | |||
| TD | 1.5 | % | ASTM D955 |
| MD | 1.5 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 0.70 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 78 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | No Break | ISO 179/1eU | |
| Impact strength of cantilever beam notch | |||
| 23℃ | 73 | kJ/m² | ISO 180-1A |
| -40℃ | 110 | J/m | ASTM D256 |
| 23℃ | 910 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 23℃ | No Break | ISO 180/1U | |
| Dart impact equipped with measuring instruments | ASTM D3763 | ||
| Energy to Maximum Load | 38.0 | J | ASTM D3763 |
| Total Energy | 54.2 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 120 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 109 | ℃ | ISO 75-2/A |
| Melting peak temperature | 310 | ℃ | ASTM D3418 |
| Melting temperature | 310 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| TD | ASTM E831 | ||
| MD | ASTM E831 | ||
| 0 to 100 ℃ | 7.7E-5 | cm/cm/℃ | ASTM E831 |
| 100 to 200 ℃ | 1.4E-4 | cm/cm/℃ | ASTM E831 |
| 0 to 100 ℃ | 8.1E-5 | cm/cm/℃ | ASTM E831 |
| 100 to 200 ℃ | 1.1E-4 | cm/cm/℃ | ASTM E831 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2410 | MPa | ASTM D638 |
| Tensile modulus | ISO 527-2 | ||
| 23℃ | 2410 | MPa | ISO 527-2 |
| 100℃ | 2000 | MPa | ISO 527-2 |
| tensile strength | ASTM D638 | ||
| -40℃ | 110 | MPa | ASTM D638 |
| 23℃ | 68.9 | MPa | ASTM D638 |
| tensile strength | ISO 527-2 | ||
| Fracture, 23 ℃ | 60.0 | MPa | ISO 527-2 |
| Yield, 23 ℃ | 70.3 | MPa | ISO 527-2 |
| Yield, 100 ℃ | 33.8 | MPa | ISO 527-2 |
| Tensile strain | ASTM D638 | ||
| Yield, -40 ℃ | 9.0 | % | ASTM D638 |
| Yield, 23 ℃ | 6.0 | % | ASTM D638 |
| Tensile strain | ISO 527-2 | ||
| Yield, 23 ℃ | 5.0 | % | ISO 527-2 |
| Yield, 100 ℃ | 4.3 | % | ISO 527-2 |
| Fracture, -40 ℃ | 12 | % | ASTM D638 |
| Fracture, 23 ℃ | 20 | % | ASTM D638 |
| Fracture, 23 ℃ | 7.0 | % | ISO 527-2 |
| Fracture, 24 ℃ | 95 | % | ISO 527-2 |
| Bending modulus | 2280 | MPa | ASTM D790 |
| Bending modulus | ISO 178 | ||
| 23℃ | 1790 | MPa | ISO 178 |
| 100℃ | 1310 | MPa | ISO 178 |
| bending strength | 109 | MPa | ASTM D790 |
| bending strength | ISO 178 | ||
| 23℃ | 70.3 | MPa | ISO 178 |
| 100℃ | 44.1 | MPa | ISO 178 |
| shear strength | 58.6 | MPa | ASTM D732 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 6.00 | mg | ASTM D1044 |
| Rockwell hardness | |||
| R-level | 120 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 110 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.045 | % | |
| Barrel rear temperature | 304 to 318 | °C | |
| Barrel front temperature | 316 to 329 | °C | |
| Processing (melt) temperature | 321 to 343 | °C | |
| Mold temperature | 70 to 90 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Maximum Load: 1050 lb (4670 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |