| About |
|---|
| Udel® P-1700 polysulfone (PSU) is a tough, rigid, high-strength thermoplastics suitable for continuous use up to 300°F (149°C). It is resistant to oxidation and hydrolysis and withstand prolonged exposure to high temperatures and repeated sterilization. Udel® P-1700 polysulfone is highly resistant to mineral acids, alkali and salt solutions. Resistance to detergents and hydrocarbon oils is good, but the resin may be attacked by polar solvents such as ketones, chlorinated hydrocarbons and aromatic hydrocarbons. These resins are also highly resistant to degradation by gamma or electron beam radiation. Electrical properties of Udel® P-1700 polysulfones are stable over a wide temperature range and after immersion in water or exposure to high humidity. The resins comply with FDA 21 CFR 177.1655 and may be used in articles intended for repeated use in contact with foods. Additionally, they are approved by the NSF, by the Department of Agriculture for contact with meat and poultry and by the 3-A Sanitary Standards of the Dairy Association. Transparent: Udel® P-1700 CL 2611 CMP Transparent: Udel® P-1700 NT 06 Transparent: Udel® P-1700 NT 11 Opaque Black : Udel® P-1700 BK 937 Opaque White: Udel® P-1700 WH 6417 Opaque White: Udel® P-1700 WH 7407 Opaque Gray: Udel® P-1700 GY 8057&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Material Status | Commercial: Active |
| Features | Steam sterilized,High pressure disinfection,Hydrocarbons,Resistance to the steam,Alkali resistant,HB,V-0,High Heat Resistance,Ethanol tolerance,Radioactive,Gamma radiation,Radiation disinfection,Biocompatible,Ethylene oxide disinfection,Solvent resistance,Hydrolysis stability,Resistance to detergents,Food contact compliance,E-beam disinfection,Heat sterilization,Good surface appearance,Good Dimensional Stability,Good flexibility,Good disinfection,Acidproof |
| Availabilitys | North America,Europe,Latin America,Asia Pacific |
| Process Methods | Thermo forming,Film extrusion,Injection Molding,Extrusion,Profile extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.24 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 343℃，2.16kg | 6.5 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.70 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 0.30 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2480 | MPa | ASTM D638 |
| tensile strength | 70.3 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 50 to 100 | % | ASTM D638 |
| Bending modulus | 2690 | MPa | ASTM D790 |
| bending strength | 106 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 69 | J/m | ASTM D256 |
| Tensile impact strength | 420 | kJ/m² | ASTM D1822 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 174 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD | 5.6E-5 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 3.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | 17 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 60 Hz | 3.03 | ASTM D150 | |
| 1 kHz | 3.04 | ASTM D150 | |
| 1 MHz | 3.02 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 60 Hz | 7.0E-4 | ASTM D150 | |
| 1 kHz | 1.0E-3 | ASTM D150 | |
| 1 MHz | 6.0E-3 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.50 mm, all colors | HB | UL 94 | |
| 4.50 mm, natural color | V-0 | UL 94 | |
| Glowing wire flammability index | IEC 60695-2-12 | ||
| 0.80 mm | 850 | ℃ | IEC 60695-2-12 |
| 1.6-6.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | IEC 60695-2-13 | ||
| 0.8 mm | 875 | ℃ | IEC 60695-2-13 |
| 1.6-6 mm | 850 | ℃ | IEC 60695-2-13 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 135 to 163 | °C | |
| Drying time | 3.5 | hr | |
| Recommended injection volume | 50 to 75 | % | |
| Processing (melt) temperature | 329 to 385 | °C | |
| Mold temperature | 121 to 163 | °C | |
| Notes |
|---|
| 1. Only Udel P-1700 NT 06 and Udel P-1700 NT 11 are NSF 51 listed. Maximum Temperature of Use: 149°C (300°F) |
| 2. Only Udel P-1700 NT 11, Udel P-1700 BK 937, Udel P-1700 WH 6417 and Udel P-1700 WH 7407 are NSF 61 listed. Tested at 82 °C (180 °F) (Commercial Hot) |
| 3. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |