| About |
|---|
| PPS-hGR30 is glass reinforced PPS compound, which is filled with glass fiber based on the PPS resin. The characteristic of PPS determine the utility of PPS resins and their compounds, which includes good mechanical properties, high creep resistance, high temperature resistance, friction resistance, flame resistance, chemical resistance, excellent electrical insulation properties, arc resistance, low mold shrinkage, good dimensional stability, and radiation resistance. Owing to its high performance, PPS-hGR30 can be used to make elements where high temperature resistance, electrical insulation are all-important in aviation; anticorrosion valves and electrical insulation parts in chemical industry; precise plugs, outer shells and high temperature resistant contactors in electronic industry; electric parts, terminal and switches in electric industry; high temperature resistant axle bearing and piston rings in mechanical industry.&& |
| Product Description | |
|---|---|
| Supplier | Deyang |
| Generic | PPS |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good flexibility,Good Dimensional Stability,Gamma radiation,Low coefficient of friction,Low contractility,Corrosion Resistant,Flame Characteristics,High Heat Resistance,Arc resistance,Solvent resistance,Insulation,V-0 |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.55 | g/cm³ | Internal Method |
| Shrinkage rate | Internal Method | ||
| MD | 0.25 | % | Internal Method |
| TD | 0.75 | % | Internal Method |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 12 | kJ/m² | Internal Method |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 267 | ℃ | Internal Method |
| Melting temperature | 282 | ℃ | Internal Method |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 2.3E+15 | ohms | Internal Method |
| Volume resistivity | 1.0E+17 | ohms·cm | Internal Method |
| Dielectric strength | 18 | kV/mm | Internal Method |
| Dielectric constant | |||
| 1 MHz | 4.00 | Internal Method |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | 100 | Internal Method | |
| tensile strength | 142 | MPa | Internal Method |
| Tensile strain | |||
| fracture | 1.7 | % | Internal Method |
| Bending modulus | 11000 | MPa | Internal Method |
| bending strength | 180 | MPa | Internal Method |
| compressive strength | 140 | MPa | Internal Method |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 110 to 140 | °C | |
| Drying time | 3.0 to 5.0 | hr | |
| Barrel rear temperature | 270 to 290 | °C | |
| Barrel middle temperature | 300 to 320 | °C | |
| Barrel front temperature | 300 to 320 | °C | |
| Nozzle temperature | 290 to 320 | °C | |
| Processing (melt) temperature | 160 to 180 | °C | |
| Mold temperature | 100 to 150 | °C | |
| Injection pressure | 50.0 to 100 | MPa | |
| Back pressure | 0.100 to 1.00 | MPa | |
| Screw speed | 40 to 100 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. HR |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |