| About |
|---|
| ADIPRENE® L 167 urethane rubber is one of a series of liquid urethane polymers which can be cured to a strong, rubbery solid by reaction of the isocyanate groups with polyamine or polyol compounds. When cured with MBCA curing agent, ADIPRENE L 167 yields vulcanizates in the 95A durometer hardness range. Lower hardness values and special properties can be obtained with other curing systems. Cured ADIPRENE L 167 has high tensile strength and resilience and excellent properties at low temperatures. It is resistant to abrasion, compression set, oils, solvents, oxidation and ozone. ADIPRENE L 167 can be cast or sprayed to produce a variety of molded goods and protective and decorative coatings.&& |
| Product Description | |
|---|---|
| Supplier | Chemtura |
| Generic | PUR-脂肪族+TDI |
| Material Status | Commercial: Active |
| Features | Antifreeze,Inoxidizability,Elastic,Good Tensile Strength,Good wear resistance,Grease resistance,Ozone resistance,Solvent resistance |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | casting |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | g/cm³ | ASTM D792 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 95 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| 100% strain | 12.4 | MPa | ASTM D412 |
| 300% strain | 23.4 | MPa | ASTM D412 |
| tensile strength | 34.5 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 400 | % | ASTM D412 |
| tear strength | |||
| — | 87.6 | kN/m | ASTM D624 |
| cracking | 26 | kN/m | ASTM D470 |
| Compression deformation | |||
| 70℃，22 hr | 40 | % | ASTM D395B |
| Basho’s elasticity | 40 | % | ASTM D2632 |
| Kappa’s modulus | ASTM D1043 | ||
| -57℃ | 552 | MPa | ASTM D1043 |
| -40℃ | 114 | MPa | ASTM D1043 |
| -18℃ | 49.3 | MPa | ASTM D1043 |
| 24℃ | 16.5 | MPa | ASTM D1043 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | |||
| NBS | 300 |
| Uncured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| Curing time | |||
| 100℃ | 1.0 | hr |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| -36 to 0 ℃ | 2.3E-4 | cm/cm/℃ | ASTM D696 |
| 0 to 24 ℃ | 1.6E-4 | cm/cm/℃ | ASTM D696 |
| 24 to 100 ℃ | 1.6E-4 | cm/cm/℃ | ASTM D696 |
| 100 to 150 ℃ | 1.2E-4 | cm/cm/℃ | ASTM D696 |
| Embrittlement temperature | < -70.0 | ℃ | ASTM D746 |
| Linear coefficient of thermal expansion | |||
| MD | ASTM D696 | ||
| Thermal conductivity coefficient | 0.12 | W/m/K | ASTM C177 |
| Thermosetting components | |||
| resin | 按重量计算的混合比: 100 | ||
| Hardening method | 按重量计算的混合比: 19 | ||
| storage stability | |||
| 85 ℃ | 6.0 | min | |
| stripping time | |||
| 100℃ | 15 | min | |
| Post curing time | |||
| 70℃ | 16 | hr |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |