LEXAN™ HP6NREU resin

About
LEXAN™ HP6NREU是一种无定形的,中低流动性的聚碳酸酯(PC)，由沙特基础工业公司提供。具有生物相容性、埃托奥和蒸汽灭菌，内部脱模。具有优异的机械、光学、电气和热性能。适合注塑加工。用于医疗器械和药物应用。符合ISO10993或USP VI等级。

Product Description
Supplier	SABIC
Generic	Polycarbonate
Material Status	Commercial: Active
Features	Internal mold release
Availabilitys	Africa & Middle East ,Asia Pacific,Europe

Technical Data
MECHANICAL	Nominal value	Unit	Test method
tensile strength
Yield, 50 mm/min	63	MPa	ISO 527
Fracture, 50 mm/min	70	MPa	ISO 527
Tensile strain
Yield, 50 mm/min	6	%	ISO 527
Fracture, 50 mm/min	120	%	ISO 527
Tensile modulus
1 mm/min	2350	MPa	ISO 527
bending strength
Yield, 2 mm/min	90	MPa	ISO 178
Bending modulus
2 mm/mim	2300	MPa	ISO 178
Taber wear and tear
CS-17，1kg	10	mg/1000cy	Internal Method

IMPACT	Nominal value	Unit	Test method
Notched impact strength of cantilever beam
23℃，80103	NB	kJ/m²	ISO 180/1U
-30℃，80103	NB	kJ/m²	ISO 180/1U
Impact strength of cantilever beam notch
23℃，80103	75	kJ/m²	ISO 180-1A
-30℃，80103	15	kJ/m²	ISO 180-1A
23℃	75	kJ/m²	ISO 180/1A
-30℃	15	kJ/m²	ISO 180/1A
23℃	NB	kJ/m²	ISO 179/1eU
-30℃	NB	kJ/m²	ISO 179/1eU
Charpy Notched Impact Strength
80 * 10 * 3, 62mm span
80 * 10 * 3, 62mm span
23℃	35	kJ/m²	ISO 179/2C

THERMAL	Nominal value	Unit	Test method
Thermal conductivity coefficient	0.2	W/m/℃	ISO 8302
Ball pressure test
125℃±2℃	passes		IEC 60695-10-2
Maximum approximation value	140	℃	IEC 60695-10-2
Linear coefficient of thermal expansion
MD：23~80℃	7.E-0.5	1/℃	ISO 11359-2
TD：23~80℃	7.E-0.5	1/℃	ISO 11359-2
Vicat Softening Temp
B50	144	℃	ISO 306
B120	145	℃	ISO 306
Hot deformation temperature
0.45 MPa, 100 mm span	127	℃	ISO 75/Be
1.8 MPa, 100 mm span	138	℃	ISO 75/Ae
Relative temperature index
Electrical performance	130	℃	UL 746B
Impact mechanical performance	125	℃	UL 746B
Non mechanical impact performance	125	℃	UL 746B

PHYSICAL	Nominal value	Unit	Test method
Shrinkage rate
MD：3.2 mm	0.5 – 0.7	%	Internal Method
Shrinkage rate
MD：3.2 mm	0.5 – 0.7	%	Internal Method
Melt Flow Rate
300℃，1.20kg	7	g/10min	ASTM D1238
Density	1.2	g/cm³	ISO 1183
Water absorption rate
Saturation, 23 ℃	0.35	%	ISO 62
23℃，50% RH	0.15	%	ISO 62
Melt Volume Rate
300℃，1.2 kg	6	cm³/10min	ISO 1133

optical performance	Nominal value	Unit	Test method
Transmittance
2.54 mm	89	%	ASTM D1003
Haze
2.54 mm	<0.8	%	ASTM D1003
Refractive index	1.586		ISO 489

Electrical performance	Nominal value	Unit	Test method
Volume resistivity	>1.E+15	ohms·cm	IEC 60093
Surface resistivity	>1.0E+15		IEC 60093
Dielectric strength
3.2 mm in oil	17	kV/mm	IEC 60243-1
Relative permittivity
50-60 Hz	2.7		IEC 60250
1 MHz	2.7		IEC 60250
Dissipation factor
50-60 Hz	0.001		IEC 60250
1 MHz	0.01		IEC 60250

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
94HB flame rating assessment	1.5	mm	UL 94
94HB flame level 2nd reference value	3	mm	UL 94
Glowing wire flammability index
850 ℃, passed through	1	mm	IEC 60695-2-12
Extreme oxygen index
LOI	25	%	ISO 4589

Process Conditions
injection molding	Nominal value	Unit	Test method
Drying temperature	120	°C
Drying time	2 – 4	hrs
Maximum water content	0.02	%
Melt temperature	290 – 320	°C
Nozzle temperature	280 – 210	°C
Front Section Zone 3 Temperature	290 – 320	°C
Temperature in Zone 2 of the middle section	280 – 310	°C
Temperature in Zone 1 of the rear section	270 – 300	°C
Hopper temperature	60 – 80	°C
Mold temperature	80 – 120	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.