| About |
|---|
| Elexar EL-3954-80 is a high performance thermoplastic elastomer designed for the electrical/wire & cable market. Elexar EL-3954-80 is a lubricated, high density grade suitable for both injection molding and extrusion.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Smoothness,Good Hardness,Halogen free,Lubricating,Moderate liquidity,High density,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.18 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 200℃，5.0kg | 13 | g/10min | ASTM D1238 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| TD, 100% strain | 2.83 | MPa | ASTM D412 |
| MD, 100% strain | 3.56 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| TD, 300% strain | 3.92 | MPa | ASTM D412 |
| MD, 300% strain | 4.70 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| fracture | 11.7 | MPa | ASTM D412 |
| MD, fracture | 8.87 | MPa | ASTM D412 |
| MD, fracture | 13.1 | MPa | ASTM D412 |
| Tensile strain | ASTM D412 | ||
| fracture | 740 | % | ASTM D412 |
| Flow rate, fracture | 640 | % | ASTM D412 |
| MD, fracture | 600 | % | ASTM D412 |
| tear strength | ASTM D624 | ||
| TD | 40.3 | kN/m | ASTM D624 |
| MD | 38.0 | kN/m | ASTM D624 |
| Compression deformation | ASTM D395B | ||
| 23℃，22 hr | 29 | % | ASTM D395B |
| 70℃，22 hr | 63 | % | ASTM D395B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore A, 1 second, injection molding | 78 | ASTM D2240 | |
| Shore A, 5 seconds, injection molding | 76 | ASTM D2240 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | < -60.0 | ℃ | ASTM D746 |
| Relative temperature index | |||
| Electrical performance | 90.0 | ℃ | UL 746 |
| Strength mechanical performance | 90.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | 42 | kV/mm | ASTM D149 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.50 mm, all colors | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Barrel rear temperature | 188 to 216 | °C | |
| Barrel middle temperature | 188 to 216 | °C | |
| Barrel front temperature | 188 to 216 | °C | |
| Nozzle temperature | 188 to 216 | °C | |
| Processing (melt) temperature | 188 to 216 | °C | |
| Mold temperature | 16 to 32 | °C | |
| Injection pressure | 1.38 to 6.89 | MPa | |
| Injection speed | Moderate-Fast | ||
| Back pressure | 0.172 to 0.345 | MPa | |
| Screw speed | 50 to 100 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Barrel 1 zone temperature | 177 to 204 | °C | |
| Barrel 2 zone temperature | 177 to 204 | °C | |
| Barrel 3 zone temperature | 177 to 204 | °C | |
| Barrel 4 zone temperature | 177 to 204 | °C | |
| Barrel 5 zone temperature | 177 to 204 | °C | |
| Nozzle temperature | 177 to 204 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C, 20 in/min |
| 3. Extruded tape |
| 4. Type 1 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |