| About |
|---|
| Features: General painting use Applications: Injection molded products for painting: Automobile parts, household appliances&& |
| Product Description | |
|---|---|
| Generic | PE |
| Material Status | Commercial: Active |
| Features | Sprayable |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.50 | g/cm³ | BS 2782 620A |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength | IEC 60811-1-2 | ||
| 100℃，168 hr | -10 | % | IEC 60811-1-2 |
| 110℃，168 hr | -16 | % | IEC 60811-1-2 |
| Changes in tensile stress during fracture | IEC 60811-1-2 | ||
| 100℃，168 hr | 15 | % | IEC 60811-1-2 |
| 110℃，168 hr | 5.0 | % | IEC 60811-1-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| deformation | IEC 60811-3-1 | ||
| 90℃ | 25 | % | IEC 60811-3-1 |
| 100℃ | 30 | % | IEC 60811-3-1 |
| Cold shock | |||
| Low temperature bending | |||
| -30℃ | pass | IEC 60811-1-4 | |
| Heat resistant stress cracking | |||
| 80℃ | pass | Internal Method | |
| Temperature index | 270 | ℃ | ISO 4589-3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Extreme oxygen index | 30 | % | ISO 4589-2 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Halogen Acid Gas Evolution | < 0.50 | % | IEC 60754-1 |
| tear strength | 8 | N/mm | BS 6469 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 90 | ||
| Shaw’s D | 40 | ||
| tensile strength | 13.5 | MPa | IEC 60811-1-1 |
| Tensile strain | |||
| fracture | 190 | % | IEC 60811-1-1 |
| Fracture, -30 ℃ | 60 | % | IEC 60811-1-4 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Barrel 1 zone temperature | 120 | °C | |
| Barrel 2 zone temperature | 130 | °C | |
| Barrel 3 zone temperature | 140 | °C | |
| Barrel 4 zone temperature | 150 | °C | |
| Melt temperature | < 170 | °C | |
| Head temperature | 160 | °C | |
| Nozzle temperature | 160 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |