| About |
|---|
| Modified Plastics MN 6/6-FG 10是一种聚酰胺66（尼龙66）产品,含有的填充物为10% 玻璃纤维增强材料。 它可以通过注射成型进行加工,在北美洲有供货。&& |
| Product Description | |
|---|---|
| Generic | PA66 |
| Material Status | Commercial: Active |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 1.7 | % | ASTM D955 |
| Water absorption rate | |||
| saturated | 7.6 | % | ASTM D570 |
| 24hr | 1.3 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃，6.4mm | 37 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 23℃，6.4 mm | 270 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 249 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 257 | ℃ | ASTM D648 |
| Vicat Softening Temp | 265 | ℃ | ASTM D1525 |
| Linear coefficient of thermal expansion | |||
| MD | 4.5E-5 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | 22 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 100 Hz | 4.10 | ASTM D150 | |
| 1 kHz | 1.90 | ASTM D150 | |
| 1 MHz | 3.70 | ASTM D150 | |
| Dissipation factor | |||
| 1 kHz | 0.030 | ASTM D150 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 89.6 | MPa | ASTM D638 |
| Tensile strain | |||
| yield | 3.5 | % | ASTM D638 |
| Bending modulus | 4550 | MPa | ASTM D790 |
| bending strength | |||
| yield | 138 | MPa | ASTM D790 |
| compressive strength | 117 | MPa | ASTM D695 |
| shear strength | 62.1 | MPa | ASTM D732 |
| Rockwell hardness | |||
| R-level | 120 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 93 | °C | |
| Processing (melt) temperature | 271 to 293 | °C | |
| Mold temperature | 93 to 104 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |