| About |
|---|
| Titanvene™ LL0335AA Titanvene™ LL0335AA is a linear low density polyethylene designed for silane crosslinked low voltage power cable insulation, casting film and inner layer for rotomolding. Titanvene™ LL0335AA characterized by high speed performance, low gel content, easy extrusion. Applications Low voltage power cable insulation for sioplas process. Casting film. Inner layer for rotomolding (Non UV) Recommended Processing Conditions Titanvene™ LL0335AA can be easily processed on normal machines at temperatures in the range of 150°C to 220°C. Food Contact Compliance Titanvene™ LL0335AA can be used in food contact applications. Please contact your nearest PT. Lotte Chemical TITAN Nusantara representative for more detail of food contact compliance statements for the specific grade.&&Titanvene™ LL0335AA Titanvene™ LL0335AA is a linear low density polyethylene designed for silane crosslinked low voltage power cable insulation, casting film and inner layer for rotomolding. Titanvene™ LL0335AA characterized by high speed performance, low gel content and easy extrusion. Applications Low voltage power cable insulation for sioplas process. Casting film. Inner layer for rotomolding (Non UV)&& |
| Product Description | |
|---|---|
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Low speed solidification point,Food contact compliance |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.930 | g/cm³ | ISO 1183/D |
| Melt Flow Rate | |||
| 190℃，2.16kg | 3.5 | g/10min | ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | 0.80 | BS 2782 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ISO 1184 | ||
| yield | 12.0 | MPa | ISO 527-2/2 |
| MD, yield | 11.0 | MPa | ISO 1184 |
| TD, yield | 12.0 | MPa | ISO 1184 |
| Tensile strain | ISO 1184 | ||
| fracture | > 800 | % | ISO 527-2/2 |
| MD, fracture | 700 | % | ISO 1184 |
| TD, fracture | 800 | % | ISO 1184 |
| Drop hammer impact | 70 | g | ISO 7765-1/A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | |||
| DSC | 124 | ℃ | ISO 3146 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric constant | 2.54 | ASTM D150 | |
| Dissipation factor | < 1.0E-4 | ASTM D150 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | 50 | ASTM D2457 | |
| transparency | 71.0 | ASTM D1746 | |
| Haze | 15 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Condition 4 |
| 3. Molded Plaque, Speed C |
| 4. Method 824A |
| 5. Speed 1 |
| 6. Method C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |