Plastiglas Sensacryl® Ultra

About
Sensacryl Ultra is a sanitary grade cell cast acrylic sheet with outstanding thermoforming properties, chemical and stain resistance and it is the best alternative for the design and fabrication of Bathtubs; shower trays, shower enclosures,bath panels,special needs baths,etc. Sensacryl Ultra can be produced in whites, pastels, bolds and marbles in a wide variety of sizes and thickness. Color matching and cut-to-size for specific requirements are available upon request. (see Table 2 for details). Sensacryl Ultra acrylic sheet has been submitted to an approved outside laboratory for compliance to the ANSI-Z-124.1, and EN-263:1997 standards for plastic materials used in hot tubs and associated equipment.&&

About

Sensacryl Ultra is a sanitary grade cell cast acrylic sheet with outstanding thermoforming properties, chemical and stain resistance and it is the best alternative for the design and fabrication of Bathtubs; shower trays, shower enclosures,bath panels,special needs baths,etc. Sensacryl Ultra can be produced in whites, pastels, bolds and marbles in a wide variety of sizes and thickness. Color matching and cut-to-size for specific requirements are available upon request. (see Table 2 for details). Sensacryl Ultra acrylic sheet has been submitted to an approved outside laboratory for compliance to the ANSI-Z-124.1, and EN-263:1997 standards for plastic materials used in hot tubs and associated equipment.&&

Product Description
Generic	SMMA
Material Status	Commercial: Active
Features	The fouling resistance,Solvent resistance,HB
Availabilitys	North America,Latin America
Process Methods	Thermo forming

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.19	g/cm³	ASTM D792
Water absorption rate
23℃，24hr	0.20 to 0.30	%	ASTM D570

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch	21 to 32	J/m	ASTM D256
Drop hammer impact	1.58	J	ASTM D3029

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	91.1	℃	ASTM D648
Melting temperature	170 to 190	℃

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	HB		UL 94

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
M-level	90 to 92		ASTM D785
Babbitt hardness	38 to 40		ASTM D2583
Tensile modulus	2210	MPa	ASTM D638
tensile strength	65.5 to 72.4	MPa	ASTM D638
Tensile strain
fracture	3.0 to 7.0	%	ASTM D638
bending strength	96.5 to 110	MPa	ASTM D790

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.