| About |
|---|
| HIGH TRANSPARENCY ZeonorFilm exhibits high transparency (92% light transmittance) and excellent turbidity (haze value <0.1%), for enhanced brightness. INERT SURFACE ZeonorFilm is manufactured from Zeon's cyclo olefin polymer (COP). COP is known for its excellent optical properties and also for being a high-purity resin. ZeonorFilm has an inert surface which makes it ideal for sensitive bio-diagnostic devices.&& |
| Product Description | |
|---|---|
| Supplier | Zeon |
| Generic | COP |
| Material Status | Commercial: Active |
| Features | Good Clarity,High purity,Optical performance |
| Availabilitys | Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.01 | g/cm³ | JIS K6760 |
| Shrinkage rate | ISO 294-4 | ||
| TD：120℃，0.10 mm | 0.060 | % | ISO 294-4 |
| MD：120℃，0.10 mm | -0.020 | % | ISO 294-4 |
| Water absorption rate | |||
| balance | < 0.010 | % | ASTM D570 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | 136 to 163 | ℃ | DSC |
| Linear coefficient of thermal expansion | |||
| MD | 7.0E-5 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | > 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 0.01 mm | 360 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 1 MHz | 2.30 | ASTM D150 | |
| Dissipation factor | |||
| 1 MHz | 5.0E-3 | ASTM D150 | |
| Arc resistance | |||
| 3.0 mm | 124 | sec | ASTM D495 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.530 | ASTM D542 | |
| Transmittance | |||
| 100 µm | 92.0 | % | JIS K7105 |
| Haze | |||
| 100 µm | < 0.10 | % | JIS K7105 |
| Dispersion coefficient | |||
| 25℃ | 56.0 | ASTM D542 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Pencil hardness | B | JIS K5401 | |
| tensile strength | ASTM D638 | ||
| MD，0.10 mm | 60.0 | MPa | ASTM D638 |
| TD，0.10 mm | 59.0 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| Flow rate, fracture, 0.10 mm | 40 | % | ASTM D638 |
| TD, fracture, 0.10 mm | 30 | % | ASTM D638 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. D line, 25°C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |